User manual MAKITA 1002 BA

[. . . ] Never carry tool by cord or yank it t o disconnect from receptacle. Keep cord from heat, oil, and sharp edges. It's safer than using your hand and it frees both hands t o operate tool. Keep proper footing and balance at all times. [. . . ] Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size t o use depending on cord length and nameplate ampere rating. The smaller the gage number, the heavier the cord. TABLE 1. MINIMUM GAGE FOR CORD SETS Total Length of Cord in Feet 0-25 I 25-50 I 51-100 I 101-150 Ampere Rating More Not More AWG Than Than 18 16 0 6 16 14 6 10 18 16 14 12 16 16 14 12 10 12 12 16 14 12 Not Recommended - 17. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. Watch what you are doing, use common sense. Before further use of the tool, a guard or other part that is damaged should be carefully checked t o determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. When leaving the planer, switch off and set it with the front base up on a wooden block, so that the blades do not contact anything. Always change both blades or covers on the drum, otherwise the resulting imbalance will cause vibration and shorten tool life. SAVE THESE INSTRUCTIONS. 4 Removing or installing planer blades CAUTION: Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blades on the drum, unscrew the four installation bolts with the socket wrench. The drum cover comes off together with the blades. \ To install the blades, first clean out all chips or foreign matter adhering to the drum or blades. Use blades of the same dimensions and weight, or drum oscillation/vibration will result, causing poor planing action and eventually tool breakdown. I Bolt I Drum Planer blac I Place the blade on the gauge base so that the blade edge is perfectly flush with the inside edge of the gauge plate. Place the adjusting plate on the blade, then simply press in the heel of the adjusting plate flush with the back side of the gauge base and tighten two screws on the adjusting plate. Now slip the heel of the adjusting plate into the drum groove, then fit the drum cover on it. Tigkten the three installation bolts evenly and alternately with the socket wrench. Drum Adjusting plate I Adjusting plate - \ / - of gauge plate I base CAUTION: Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. 5 Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Knob 1 Adjusting front base The front base is factory-adjusted to allow concave cuts with a radius of 320 mm. For concave cuts with the tool's minimum radius of 300 mm, loosen the wing bolt on either side and raise the front base as far as it will go. Then retighten the two wing bolts firmly to secure the front base. Wing bolt Switch action To start the tool, simply pull the trigger. [. . . ] Both carbon brushes should be replaced at the same time. Use only identical carbon brushes. I Use a screwdriver to remove the chip cover. Limit mark 1 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. // Sdrewdriver Chipcover I Brush holder cap \ To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 8 ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Planer blade Width 110 mm (4-3/8") Part No 793008-8 Planer blade (Material Tungsten-carbide) Width 110 m m (4-3/8") Part No 7930096 Sharpening holder assembly Part No. 123062-2 9 Seo. -ll-'97 US 110 mm (4-318") CURVED PLANER Model 1002 BA e Note: The switch and other part configurations may differ from country to country. 10 MODEL 1002 BA Sep. -11-'97 DESCRIPTION O "' ;M US , &, MACHINE ___ 1 2 3 4 5 6 1 1 1 2 2 2 ED DESCRIPTION 1 1 1 1 1 1 1 Belt cover Ball Bearing 6200LB Insulation Washer ARMATURE ASSEMBLY (With Item 34. [. . . ]