User manual MAKITA 4330DWA

[. . . ] Cordless Jig Saw MODEL 433ODWA MODEL 4330DZ INSTRUCTION MANUAL SPECIFICATIONS Length of stroke 26 m m (1") Max. c u t t i n g capacities Wood I(5-5/16"] 1 135mm I Mild steel I Strokes Overall ]!$$T I Aluminum 2 0 mm (, 3/16, , 1 I per minute 2, 800 I length I 1 weight Net 280mm (11") 2'6 kg ( 5 . 7 Ibs) * Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. [. . . ] Incorrect reassembly may result in a risk of electric shock or fire. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 6 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (50OF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. Always cover the battery terminals w i t h the battery cover when the battery cartridge is not used. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. (1I Do not touch the terminals w i t h any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) not expose battery cartridge t o water or rain. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 5OoC (122OF). Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. SAVE THESE INSTRUCTIONS. 7 Installing or removing the saw blade CAUTION: Always be sure that the tool is switched off and battery removed before installing or removing the blade. To install the blade, loosen the screw on the blade holder. Loosen \ Screw With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits properly in the groove of the roller. Then firmly tighten the screw to secure the blade. CAUTION: *Always secure the blade firmly. Insufficient securing of the blade may cause blade breakage or serious injury. *Always clean out the blade holder before installing the blade. Chips or foreign matter on the blade holder may cause insufficient securing of the blade. Use a lubricant or cutting oil between the blade and roller when cutting iron or composition board, etc. Failure to do so will shorten the service life of your blade and roller or lead to potentially dangerous blade breakage. 8 Installing the universal shank jig saw blade CAUTION: Always be sure that the tool is switched off and battery removed before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6. 35 mm ( 1/4 " 1. Insert the blade into the blade holder as far as it will go. Make sure that the end of the blade shank reaches the bottom of the inner slit and tighten the bolt securely with the hex wrench. The end of the blade 7 shank should reach the bottom of the inner slit Bolt Selecting the cutting action This tool can be operated with an orbital or a straight line cutting action. [. . . ] 51 Teeth per inch 792428-3 24 Part No, Effective cutting blade length 65 mm (2-W') 80 mm (3-1/8") Hose 19-2. 5 (3-1/8") No. 8-24 NO. 8-25 Part No. 192108-5 I I No. 59 I 792429-1 I 1792430-6 I 8 I 8 I 80" I I I No. 6-23 1792474-6 7924754 792476-2 65 mm (2-1/2") 75 mm (3") 50 mm (2") 12 I I ; ; 24 6 I I 50mm(2") 80 mm (3-1/8") 50 mm (2") No. [. . . ]