User manual MAKITA 5046DWDE

[. . . ] Cordless Circular Saw with Dust Collection 165 mm (6-112") MODEL 5026DA, 5026DB 160 mm (6-114") MODEL 5036DA, 5036DB 160 mm (6-114") MODEL 5046DA. 5046DB 165 mm (6-112") MODEL 5026DWA, 5026DWB With High Capacity Battery Charger 160 mm (6-114") MODEL 5036DWA, 5036DWB With High Capacity Battery Charger 160 mm (6-1/4") MODEL 5046DWA, S046DWB With High Capacity Battery Charger INSTRUCTION MANUAL SPECIF1CAW ON S MODE7 Blade diameter 1 I Cutting depth 1 No I ~ ~ I I I ~ Overall length e ~ ~ I d Net weight 5026D 5036D I I 165 mm 16. 112") 55 mm 12-3/16") I 2, 400 2, 400 338 mm 113-5116', ) 3. 8 kg (8. 4 I Ibs) 338 mm (13-5116") 3. 8 kg 18. 4Ibs) I 160 mm 16-114") 1 53 mm (2-1/16"]I Battery Cartridge 1822 Model DC1801 High Capacity Battery Charger Voltage Input A. C. 7. 2 V - 18 V Charging time 18 V Battery Cartridge 1833 60 min. Model DC1801 High Capacity Battery Charger Voltage Input A. C. 7. 2 V ~ Charging time 18 V 18 V 65 min. GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! [. . . ] 2 5 Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK. Use extra caution when making a "Pocket Cut" into existing walls or other blind areas. The protruding blade may cut objects that can cause KICKBACK. NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump backwards over your hand, possibly causing severe injury. 1 Fig. 3 12. Before cutting be sure depth and bevel adjustments are tight. 13. Avoid Cutting Nails. Inspect for and remove all nails from lumber before cutting. Place the wider portion of the saw base o n that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. 4 illustrates the RIGHT way t o cut off the end of a board, and Fig. If the workpiece is short or small, clamp it down. DON'T TRY TO HOLD SHORT PLACES BY HAND! Fig. Fig. Never attempt t o saw w i t h the circular saw held upside down in a vise. This is extremely dangerous and can lead t o serious accidents. Fig. Before setting the tool down after completing a cut, be sure that the lower (telescoping) guard has closed and the blade has come t o a complete stop. 7 SYMBOLS The followings show the symbols used for tool. v - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . volts direct current no load speed revolutions or reciprocation per minute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . n , . . . /min 8 IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE 1. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. CAUTION - To reduce risk of injury, charge only MAKITA Battery Cartridge 7000, 7001, 7002, 7033, 7100, 7120, 9000, 9001, 9002, 9033, 9100, 9101, 9102, 9120, 9122, 9133, 1200, 1201, 1202, 1210, 1211, 1220, 1222, 1233, 1422, 1433, 9101A. Other types of batteries may burst causing personal injury and damage. [. . . ] Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced a t the same time. Use only identical carbon brushes. Limit mark Use a screwdriver to remove the brush holder caps. [. . . ]