User manual MAKITA 6223DWE

[. . . ] Equipped with Electric Brake MODEL 6223DE MODEL 6223DWE With Fast Charger INSTRUCTION MANUAL SPECIFICAT10 NS Capacities Steel 10 mm (318") 9 No load speed Machine screw Dimensions Wood Wood screw IRPM) iL x W x HI Net weight 1. 5 kg (3. 1 lbsl I 15 mm 1518") I 5. 1 mm x 35 mm 13/16" x 1-318") I 6 m m 1114") I 1 ~ 700 1 202 mm x 94 mm x 221 mm 17-15/16" x 3-11/16" x 8-3/4'1 Battery Cartridge 1220 Model DC1290 Fast Charger Voltage Input output Charging time 12 v 1 A. C. only 50 Hz - 60 Hz D. C. 9. 6 V, 12 V 1 1 Hr. * Manufacturer reserves the right t o change specifications without notice. * Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! [. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . no load speed alternating or direct current Class II Construction splash-proof construction watertight construction revolutions or reciprocation per minute number of blow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRlDGE I. SAVE THESE INSTRUCTIONS - This manual Length of Cord (Feet) AWG Size of Cord 25 18 50 18 100 18 150 16 9. Do not operate charger w i t h damaged cord or plug - replace them immediately. IO. Do not operate charger if it has received a sharp blow, been dropped, wise damaged in any way; take it t o a qualified serviceman. or other- 1 1 . Do not disassemble charger or battery cartridge; take it t o a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire. 12. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning. Turning off controls will not reduce this risk. 6 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do n o t charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3. Do n o t allow anything t o cover or clog the charger vents. 4. Always cover the battery terminals w i t h the battery cover w h e n the battery cartridge is n o t used. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. (1) Do n o t touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) n o t expose battery cartridge t o water or rain. Do n o t store the tool and Battery Cartridge in locations where the temperature may reach or exceed 5OoC (122OF). Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. SAVE THESE INSTRUCTIONS. 7 Installing or removing battery cartridge *Always switch off the tool before insertion or removal of the battery cartridge *To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. *Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the fast charger. Insert the cartridge fully into the port so that it resets on the charger port floor. [. . . ] The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. Bits Size Phillips Part No. Drill bits Tested best in Makita driver-drills for s m o o t h fast drilling and more holes per b a t t e r y change. For drilling in metal, w o o d and plastic. [. . . ]