User manual MAKITA 6913DW

[. . . ] Wear protective hair covering t o contain long hair. Also use face or dust mask if cutting operation is dusty. Never carry tool by cord or yank it t o disconnect from receptacle. Keep cord from heat, oil, and sharp edges. [. . . ] When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. Watch what you are doing, use common sense. Don't operate tool when you are tired. Before further use of the tool, a guard or other part that is damaged should be carefully checked t o determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. Have defective switches replaced by authorized service center. Don't use tool if switch does not turn it on and off. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. This tool should be grounded while in use to protect the operator from electric shock. To start the tool, simply pull the lower part of the switch for clockwise, the upper part for counterclockwise. Release the switch t o stop. Counterclockwise CAUTION : 0 Before plugging in the tool, always check t o see that the trigger switch actuates properly and returns to the "OFF" position when released. 0 Change the direction of rotation only when the tool comes t o a complete stop. Changing it before the tool stops may ruin the tool. 6 Operation The proper tightening torque may differ depending upon the kind or size of the bolt. The relation between tightenting torque and tightening time is shown in the figure below. kg . cm I f f 14. 000 11. 0101 13. 000 19381 12, 000 , Ibrl 18661 1 1. 000 17941 10. 000 17221 9. 000 16491 Y 1 5 ' 8, 000 (5771 7. 000 (5051 6. 000 14331 4. 000 (2881 3. 000 (2161 2. 000 11441 1. 000 1721 0 2 3 4 5 6 Hold the tool firmly and place the socket over the bolt or nut. Turn the tool on and tighten for the proper tightening time. NOTE : 0 Hold the tool pointed straight a t the bolt or nut without applying excessive pressure on the tool. 0 Excessive tightening torque may damage the bolt or nut. 7 The tightening torque i s affected by a wide variety of factors including the following. After tightening, always check the torque with a torque wrench. Socket Failure t o use the correct size socket will cause a reduction in the tightening torque. * A worn socket (wear on the hex end or square end) will cause a reduction in the tightening torque. 2. Bolt *Even though the torque coefficient and the class of bolt are the same, the proper tightening torque will differ according t o the diameter of bolt. [. . . ] The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Extension bar Recommended for work in tight places where footing is poor or in spots where the conventional socket will not reach. 783203-8 0 Steel carrying casu Part No. 823031-0 10 Mar-22-'88 EN 25. 4m m (1") IMPACT WRENCH Model 6913DW Note: The switch, noise suppressor and other part configurations may differ from country to country. 11 June-14-'90 US ITEM A&, 1 1 1 1 1 1 1 2 2 2 1 2 1 1 1 1 1 32 1 1 2 1 1 1 1 2 1 1 DESCRIPTION LkM & ` !, , . MACHINE 29 30 31 32 33 34 4 1 4 4 1 2 2 1 1 1 1 2 2 2 2 1 1 1 2 1 1 1 2 1 1 1 1 1 DESCRIPTION MACHINE ~ 1 2 Bumper Hammer Case Flat Washer 35 Ring Spring 22 Anvil Flat Washer 36 Internal Gear 82 P, " 10 Needle Bearing 1012 spur Gear 37 Spindle Steel Ball 10 3 Flat Washer 35 Ring 79 Compression Spring 36 Compression Spring 49 Flat Washer 36 Steal Ball 4 8 Hammer Ball Bearing 6007LLB P, " 5 Bearing Housing Ball Bearing 151 lLLB Fan 90 ARMATURE ASSEMBLY (With Item 23 - 25 38 & 391 Hex Bolt M5xBO IWith Washerl Baffle Plate FIELD 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 400 40 1 402 403 Rivet 0 - 5 Name Plate Spring Washer 6 Hex Socket Head Bolt M6x60 Motor Housing Insulation Washer Pan Head Screw M5x14 [With Washer1 Rear Cover Cushion Ring Ball Bearing 620oCLB oust Seal 10 Carbon Brush Brush Holder Cap Brush Holder Cap Cover Pan Head Screw M4x10 (With Washerl Cord Guard Cord Strain Relief Pan Head Screw M4x14 (With Washer1 Pan Head Screw M4x8 [With Washerl Switch Handle Cover Pan Head Screw M4x25 (With Washer1 Pan Head Screw M4x8 IWith Washer1 Grip 37 Grip Base Cap Square Neck Bolt Max35 Belt - -- Note The switch and other part specifications may differ from country to Country f MAKmA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. [. . . ]