User manual MAKITA AG125(1)

[. . . ] Air Nailer MODEL AG090 MODEL AG125 INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w. c o m SPECIFICATIONS Model AG090 AG125 Air pressure Nail length Diameter of nail head 7. 5 - 11. 0 mm (0. 295" - 0. 433") Overall length 260 mm (10-1/4") Min. hose diameter 6. 5 mm (1/4") Net weight 1. 3 kg (2. 9 lbs) 32 - 90 mm (1-1/4" - 3-1/2") 4. 5 - 8. 5 kgf/cm G (65 - 120 PSIG) 75 - 125 mm (3" - 5") 2 · Manufacturer reserves the right to change specifications without notice. [. . . ] For proper lubrication, the tool must be fired a couple of times after pneumatic tool oil is introduced. Selecting nails Nail guide · D1 D2 Gauge CAUTION: Do not drive hardened steel nails or stainless steel nails into concrete or steel plate. If you do so, the nailer may be adversely affected. Always check the size of the nail head with the gauge on the nail guide before loading the nailer. Different size nails may be mixed up in the nails you purchase locally. Do not use nails with a head size larger than D1 or smaller than D2. Nails with a head size larger than D1 cannot be inserted into the nail guide. Nails with a head size smaller than D2 may move into the contact arm and cannot be driven. 11 Loading nailer · Nail head Nail shank Nail tip CAUTION: Be careful not to touch the trigger when loading the nail. When loading nail into the nailer, grip the nail by the shank, not the tip. · Hold the nail shank lightly and insert the nail head into the nail guide until the nail is held firmly by the magnet. Magnet Nail Nail guide Contact arm Adjusting depth of nailing · CAUTION: Always disconnect the hose before adjusting the depth of nailing. Adjuster To adjust the depth of nailing, turn the adjuster so that the arrow above the adjuster will point to the number indicated on the adjuster. The depth of nailing is the deepest when the arrow points to the number 1. It will become shallower as the arrow points to higher number. 1. 5 mm (1/16") increments per graduation. If nails cannot be driven deep enough even when the arrow points to the number 1, increase the air pressure. Connecting air hose Air fitting Air socket Slip the air socket of the air hose onto the air fitting on the nailer. Be sure that the air socket locks firmly into position when installed onto the air fitting. A hose coupling must be installed on or near the tool in such a way that the pressure reservoir will discharge at the time the air supply coupling is disconnected. 12 Operation Driving surface · CAUTION: Make sure the safety system is in working order before operation. Trigger To start driving, place the tip of the nail against the driving surface and pull the trigger. At the start of driving, apply gentle downward pressure on the nailer in the arrow direction to hold the nail firmly. When the impact of the contact arm stops, the driving operation is over. If the nail is not driven deep enough, place the ejection port of the nailer over the nail head. Press the nailer against the driving surface firmly and pull the trigger to do additional driving of the nail. NOTE: · The nailer will not operate unless you apply sufficient pressure to the contact arm. If this occurs, apply forward pressure to the nailer again while pulling the trigger to start operation. Nailing with one or two impacts 1 Set the tip of the nail firmly against driving surface. 2 Pull trigger. When you need to position a nail or drive a shallow nail: 1. Set the tip of the nail firmly against the driving surface. Withdaw the nailer from the driving surface immediately after one or two impacts. NOTE: · The impacts will continue as long as you keep the nailer pressed up against the driving surface, even if you release the trigger. 3 Withdaw nailer from driving surface immediately after one or two impacts. Nailing in metal plate holes Metal plate Hole CAUTION: · Always make sure that the tip of the nail is inserted in the hole in the metal plate before you start nailing. 13 Air exhaust Exhaust cover Air exhaust direction can be changed easily by rotating the exhaust cover. [. . . ] Louis, MO 63126-2221 (314) 909-9889 OKLAHOMA 552 E. Memorial Road Oklahoma City, OK 73114 (405) 752-2655 VIRGINIA 5760 Northampton Blvd, . 102 Virginia Beach, VA 23455 (757) 460-0280 INDIANA 8403 Michigan Road, Unit 1 Indianapolis, IN 46268 (317) 334-9980 NEBRASKA 4129 S. Omaha, NE 68127 (402) 597-2925 OREGON 828 19th Avenue. , N. W. [. . . ]