User manual MAKITA DHR202RMJ

[. . . ] γίες χρήσεως Kullanma kılavuzu NL Snoerloze boorhamer DK Akku borehammer GR Περιστροφικό σφυρί με μπαταρία TR Akülü Kırıcı Delici DHR164 DHR165 4 1 2 3 1 015179 2 012128 5 6 7 3 015659 4 015180 7 8 A 9 B 5 10 015181 6 015182 11 12 007378 13 7 2 8 007377 14 15 18 19 20 16 17 21 9 007370 10 22 001296 22 23 23 11 007372 12 007373 25 24 13 015183 14 001300 26 15 015184 16 002449 3 27 29 30 28 17 015185 18 32 007048 33 31 19 34 35 001145 20 015186 21 015187 4 ENGLISH (Original instructions) Explanation of general view 1 2 3 4 5 6 7 8 9 10 11 12 Red indicator Button Battery cartridge Star marking Indicator lamps Check button Switch trigger Lamp Reversing switch lever Lock button Rotation with hammering Action mode changing knob 13 14 15 16 17 18 19 20 21 22 23 24 Rotation only Grip base Side grip Loosen Tighten Teeth Protrusion Bit shank Bit grease Bit Chuck cover Depth gauge 25 26 27 28 29 30 31 32 33 34 35 Dust cup Blow-out bulb Chuck adapter Keyless drill chuck Sleeve Ring Limit mark Holder cap cover Recessed part Brush holdre cap Screwdriver SPECIFICATIONS Model Concrete Capacities Steel Wood No load speed Blows per minute Overall length Rated voltage Battery cartridge Net weight D. 5 kg GEB046-2 DHR165 • Due to our continuing program of research and development, the specifications herein are subject to change without notice. € Specifications and battery cartridge may differ from country to country. € Weight, with battery cartridge, according to EPTAProcedure 01/2003 ENE042-1 CORDLESS ROTARY HAMMER SAFETY WARNINGS 1. [. . . ] In this situation, let the battery cool before pulling the trigger switch again. € Low battery voltage: The remaining battery capacity is too low and the tool will not operate. In this situation, remove and recharge the battery. 5) CAUTION: • Do not look in the light or see the source of light directly. Pull the switch trigger to light up the lamp. The lamp keeps on lighting while the switch trigger is being pulled. The light automatically goes out 10 – 15 seconds after the switch trigger is released. NOTE: • Use a dry cloth to wipe the dirt off the lens of the lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. € Do not use thinner or gasoline to clean the lamp. 3) (Only for battery cartridges with “B” at the end of the model number. ) Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for few seconds. indicator lamps Remaining capacity Lighted Off Blinking 75% to 100% 50% to 75% 25% to 50% 0% to 25% Charge the battery. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. CAUTION: • Always check the direction of rotation before operation. € Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. € When not operating the tool, always set the reversing switch lever to the neutral position. Selecting the action mode Rotation with hammering (Fig. 7) For drilling in concrete , masonry , etc. [. . . ] Also, the drill chuck will come off when reversing the tool. € Pressing excessively on the tool will not speed up the drilling. Remove holder cap covers by inserting the slotted bit screwdriver into the recessed part in the tool and lifting it up. Use a screwdriver to remove the brush holder caps. [. . . ]