User manual MAKITA DPC7341

[. . . ] Always follow safety precautions in the Instruction and Safety Manual. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. A, Inc warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fail to conform with EPA regulations during its warranty period. [. . . ] If any of these symptoms occur, see a physician!To protect unusable cutting discs from misuse, destroy them before disposal. When the Power Cut is worn out or damaged beyond repair, have it disposed of or recycled in an environmentally sound manner. If necessary, consult your local authorities. 0 Idling speed 1/min 2, 500 2, 500 Clutch engagement speed 1/min 3, 800 3, 800 Engine speed limitation 1/min 9, 350 ± 145 9, 350 ± 145 Max. Spindle speed 1/min 4, 300 4, 300 Sound pressure level at the operators ear dB (A) 97 104 Sound pressure level at the bystander's position (50 ft) dB (A) 84 86 Vibration acceleration ah, w per EN 1454 - Tubular handle (idle/rated spindle speed) m/s2 6/5 7/6 8/6 8/7 - Rear handle (idle/rated spindle speed) m/s2 Carburetor (diaphragm carburetor) Type WALBRO WJ-123 Ignition system (with speed limitation) Type electronic NGK BPMR 7A / BOSCH WSR 6F / CHAMPION RCJ 6Y Spark plug Type Electrode gap in (mm) . 1) Mixture ratio (fuel/two-stroke oil) - when using MAKITA Synthetic oil 50:1 50:1 - when using other synthetic oil (quality grade JASO FC or ISO EGD) 50:1 50:1 Cutting disc for 80 m/sec. 965 300 470 965 300 470 Overall weight (tanks empty, without cutting disc) lb 21. Torque Nm Idling speed 1/min Clutch engagement speed 1/min Engine speed limitation 1/min Max. Spindle speed 1/min Sound pressure level at the operators ear dB (A) Sound pressure level at the bystander's position (50 ft) dB (A) Vibration acceleration ah, w per EN 1454 - Tubular handle (idle/rated spindle speed) m/s2 - Rear handle (idle/rated spindle speed) m/s2 Carburetor (diaphragm carburetor) Type Ignition system (with speed limitation) Type Spark plug Type Electrode gap in (mm) Fuel consumption at max. load per ISO 8893 kg/h Specific consumption at max. Load per ISO 8893 g/kWh Fuel tank capacity fl oz (l) Mixture ratio (fuel/two-stroke oil) - when using MAKITA Synthetic oil - when using other synthetic oil (quality grade JASO FC or ISO EGD) Cutting disc for 80 m/sec. Overall weight (tanks empty, without cutting disc) lb Identification plate (12) Indicate when ordering spare parts Serial number Handle Filter cover for air filter and spark plug cap Cover lock Tubular handle Muffler Protection hood Grip V-belt tension adjusting screw Retaining nuts Stand Carburetor adjustment opening Identification plate Fuel tank with handle Decompression valve Starter grip Air intake Combination Start/Stop (I/O) switch, choke Stop knob for halfway throttle Safety locking button Throttle lever Tank cap (fuel) Starter housing with starter Cutting disc Disc bolt Spring washer Hold opening Always turn off the engine and pull off the spark plug cap before doing any work on the Power Cut!Start the Power Cut only after complete assembly and inspection. For the the following work, use the assembly tools included with delivery: 1. Place the Power Cut on a stable surface and carry out the following assembly steps: To do this, take off the filter cover (see the chapter on Cleaning / changing the air filter). Before taking the foam filter out of the package, knead it thoroughly. Hinweis: The arbor hole of the cutting disc must be an exact fit with the arbor or shaft. If the arbor hole is larger, it must be fitted with an adapter ring (*). Make sure the cutting disc is installed so it turns in the right direction, if a direction is marked on the disc. Turn the disc slowly until the stop hole of the V-belt pulley is visible in the cutting arm cover (10). NOTE: Tighten the screw firmly (30 ± 2 Nm), as otherwise the cutting wheel may slip during cutting. [. . . ] Original spare parts and accessories can be obtained from your local dealer. He will also have the spare part lists to determine the required spare part numbers, and will be constantly informed about the latest improvements and spare part innovations. Please bear in mind that if parts other than original MAKITA spare parts are used, this will automatically invalidate the MAKITA product guarantee. We will furthermore not accept any liability damages arising from the use of non-MAKITA spare parts. [. . . ]