User manual MAKITA GA5030KX

[. . . ] ENGLISH (Original instructions) INSTRUCTION MANUAL Angle Grinder GA4030 GA4530 GA5030 009421 DOUBLE INSULATION IMPORTANT: Read Before Using. 1 ENGLISH (Original instructions) SPECIFICATIONS Model Depressed center wheel diameter Spindle thread Rated speed (n)/No load speed (n0) Overall length Net weight Safety class · Specifications may differ from country to country. · Weight according to EPTA-Procedure 01/2003 END202-6 GA4030 100 mm M10 11000 min-1 266 mm 1. 7 kg GA4530 115 mm M14 11000 min-1 266 mm 1. 8 kg /II GA5030 125 mm M14 11000 min-1 266 mm 1. 8 kg · Due to our continuing programme of research and development, the specifications herein are subject to change without notice. For Model GA4030 ENG102-3 Symbols The following show the symbols used for the equipment. Be sure that you understand their meaning before use. DOUBLE INSULATION Wear safety glasses. [. . . ] c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel's movement at the point of snagging. d) Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause loss of control or kickback. e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickback and loss of control Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations: a) Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe. b) The guard must be securely attached to the power tool and positioned for maximum safety, so the least amount of wheel is exposed towards the operator. The guard helps to protect operator from broken wheel fragments and accidental contact with wheel. c) Wheels must be used only for recommended applications. For example: do not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter. d) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges. e) Do not use worn down wheels from larger power tools. Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst. Additional Safety Warnings Specific for Abrasive Cutting-Off Operations: a) Do not "jam" the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage. b) Do not position your body in line with and behind the rotating wheel. [. . . ] Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direction. 9 Operation with abrasive cut-off / diamond wheel (optional accessory) 1 2 3 4 A 009429 B 1. Wheel guard for abrasive cut-off wheel/diamond wheel 010855 The direction for mounting the lock nut and the inner flange varies by wheel thickness. Refer to the table below. 100 mm (4") Abrasive cut-off wheel Diamond wheel Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more 1 2 16 mm (5/8") 16 mm (5/8") 20 mm (13/16") 1 4 20 mm (13/16") 3 3 3. Abrasive cut-off wheel 115 mm (4 - 1/2") / 125 mm (5") Abrasive cut-off wheel Diamond wheel Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more 1 2 22. 23 mm (7/8") 22. 23 mm (7/8") 22. 23 mm (7/8") 1 4 22. 23 mm (7/8") 3 1. [. . . ]