User manual MAKITA HR2300X9

[. . . ] γίες χρήσεως NL Boorhamer / Combinatiehamer E P Martillo Rotativo / Martillo Rotativo Combinado Martelo Rotativo / Martele Combinado DK Borehammer / Kombinationshammer GR Περιστροφικ σφυρί / Σφυρί συνδυασμού HR2300 HR2310T HR2600 HR2601 HR2610 HR2610T HR2611F HR2611FT 1 2 3 1 B A 4 010720 2 5 010721 6 010722 7 011561 3 8 4 10 9 6 7 11 12 011562 5 10 6 010723 12 11 010724 7 2 8 010726 14 15 13 9 010725 10 010713 16 17 18 11 003150 12 010714 18 19 12 13 010715 14 20 2 010727 21 15 010728 16 010716 3 22 23 2 17 23 010717 18 010718 24 22 19 25 15 010719 20 18 010731 24 19 011506 21 26 22 27 010733 28 23 4 010734 24 011507 29 31 30 31 32 28 28 012895 25 26 012896 27 011505 28 010729 33 29 002449 30 5 011564 34 35 6 011560 7 011561 31 32 5 9 8 36 37 7 6 9 33 011562 34 011563 24 35 010736 6 ENGLISH (Original instructions) Explanation of general view 1 2 3 4 5 6 7 8 9 10 11 12 13 Switch trigger Lock button Lamp Reversing switch lever Quick change chuck for SDSplus Change cover line Change cover Spindle Quick change drill chuck Rotation with hammering Rotation only Action mode changing knob Hammering only 14 15 16 17 18 19 20 21 22 Protrusions Grooves Bit shank Bit grease Bit Chuck cover Grip base Depth gauge Toothed side of hex hole marking on the grip base 23 Toothed side of the depth gauge 24 Dust cup 25 symbol 26 Attachment at the foot of dust cup 27 Bellows 28 Attachment 29 Inside periphery 30 Carved side 31 Cap 32 Groove 33 Blow-out bulb 34 Chuck adapter 35 Keyless drill chuck 36 Sleeve 37 Ring SPECIFICATIONS Model Concrete Core bit Capacities Diamond core bit (dry type) Steel Wood No load speed (min–1) HR2300 HR2310T HR2600 HR2601 HR2610 HR2610T HR2611F HR2611FT 26 mm 68 mm 80 mm 13 mm 32 mm 0 – 1, 200 0 – 4, 600 356 mm 2. 0 kg 68 mm 80 mm 13 mm 32 mm 23 mm 68 mm 70 mm 13 mm 32 mm Blows per minute Overall length Net weight Safety class • Due to our continuing program of research and development, the specifications herein are subject to change without notice. € Specifications may differ from country to country. Exposure to noise can cause hearing loss. [. . . ] If it is still difficult to turn the knob, rotate the chuck again. Bit angle (when chipping, scaling or demolishing) For Models HR2310T, HR2610, HR2610T, HR2611F, HR2611FT The bit can be secured at the desired angle. To change the bit angle, rotate the action mode changing knob to the O symbol. 14) Rotate the action mode changing knob to the g symbol. 15) Then make sure that the bit is securely held in place by turning it slightly. 16) Press the lock button on the grip base in the direction of arrow shown in the figure and with the lock button being pressed insert the depth gauge into the hex. 17) At this time, the depth gauge needs to be inserted so that its toothed side is directed to the toothed side of hex hole marking on the grip base as shown in Fig. Adjust the depth gauge to the desired depth by moving it back and forth while pressing the lock button. After the adjustment, release the lock button to lock the depth gauge. 19) NOTE: • Inserting the depth gauge with its toothed side not directed to the toothed side of hex hole marking on the grip base as shown in the figure does not allow the depth gauge to be locked. Torque limiter The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning. CAUTION: • As soon as the torque limiter actuates, switch off the tool immediately. This will help prevent premature wear of the tool. € Bits such as hole saw, which tend to pinch or catch easily in the hole, are not appropriate for this tool. This is because they will cause the torque limiter to actuate too frequently. 20) Use the dust cup to prevent dust from falling over the tool and on yourself when performing overhead drilling operations. Attach the dust cup to the bit as shown in Fig. The size of bits which the dust cup can be attached to is as follows. Bit diameter Dust cup 5 Dust cup 9 006406 ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Install the side grip so that the protrusions on the grip fit in between the grooves on the tool barrel. [. . . ] 31) 10 MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. € Never use gasoline, benzine, thinner, alcohol or the like. discoloration , deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. [. . . ]