User manual MAKITA HT48

[. . . ] This will assist you to obtain the best possible result from your DOLMAR Brush Cutter. 19 SYMBOLS You will note the following symbols when reading the instruction manual. Users insufficiently informed will risk danger to themselves as well as others due to improper handling. € It is recommended only to lend the brush cutter to people who have proven to be experienced with brush cutters. [. . . ] First Aid In case of accident, make sure that a first-aid box is available in the vicinity of the cutting operations. Immediately replace any item taken from the first aid box. 5 Never straighten or weld damaged cutting tools. Cardboard is a basic raw material and is therefore consequently reusable or suitable for recycling (waste paper recycling). EC-DECLARATION OF CONFORMITY Model; MS-4211 We declare under our sole responsibility that this product is in compliance with the following standards of standardized documents, ISO11806, EN55012 in accordance with Council Directives, 89/392/EEC, amended 98/37/EEC, 93/68/EEC, 89/336/EEC, amended 92/31/EEC. Measured Sound Power: 114 dB Guarantee Sound Power: 118 dB These sound power levels wear measured in accordance with Council Directive, 2000/14/EC. 38, 22045 Hamburg, Germany Rainer Bergfeld Managing Director 6 TECHNICAL DATA Model MS-4211 U handle Dimensions : length x width x height (without cutting blade) Mass (without plastic guard and cutting blade) Volume (fuel tank) Engine displacement Maximum engine performance Engine speed at recommended max. Spindle speed Maximum spindle speed (corresponding) Fuel consumption Specific fuel consumption Idling speed Clutch engagement speed Carburetor (Diaphragm - carburetor) Ignition system Spark plug Electrode gap Idling Racing or W. 0 25 : 1 13/19 Right handle (Rear grip) Vibration per ISO 79161) Left handle (Front grip) Sound pressure level average to ISO 79171) Sound power level average to ISO 108841) Mixture ratio (Gasoline : DOLMAR 2-stroke oil) Gear ratio 1) The data is prepared taking equally into account the idling and racing or wide open throttle speed operating modes. 7 DESIGNATION OF PARTS MS-4211 Brush Cutter GB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 DESIGNATION OF PARTS Fuel Tank Rewind Starter Air Cleaner I-O Switch (on/off) Spark Plug Exhaust Muffler Clutch Case Hanger Handle Throttle Lever Control Cable Shaft Protector Gear Case Handle Holder Cutter Blade Fuel Filler Cap Starter Knob Choke Lever Exhaust Pipe Primer Pump 8 MOUNTING OF HANDLE CAUTION: Before doing any work on the brush cutter, always stop the engine and pull the spark plug connector off the spark plug. CAUTION: Start the brush cutter only after having assembled it completely. Refuel either in a well ventilated room or outdoors. Do not inhale fuel vapors, avoid any contact of fuel or oil with your skin. Mineral oil products degrease your skin. fuel may contain substances similar to solvents. in addition , allergic reactions may occur. Eyes can be irritated by contact with oil. If oil comes into your eyes, immediately wash them with clear water. If your eyes are still irritated, see a doctor immediately. observe the Safety Instructions on page 4. Fuel and oil mixture The engine of the brush cutter is a high-efficiency two-stroke engine. It is run with a mixture of fuel and two-stroke engine oil. [. . . ] € Check the functioning of the I-O switch, the lock-off lever, the control lever, and the look button. Cleaning of air cleaner – Raise the lock lever (1) of the air cleaner cover and release the lock. € Hold the right and left sides of the air cleaner cover, press it to the inside and then remove it. (1) – Push the choke lever (2) up (arrow), to prevent dirt particles from entering the carburetor. [. . . ]