User manual MAKITA LS1011N

[. . . ] Slide Compound Saw Equipped with Electric Blade Brake 255 mm (10") MODEL LS1011N 002167 DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Blade diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 mm (10") Hole diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miter angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Left 45°, Right 57° Max. [. . . ] 4. Blade case Arrow Saw blade Arrow 002176 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, insert the elbow into the dust spout on the blade case and fit the bag's entry port over the elbow. 1 2 3 1. Fastener When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. NOTE: If you connect a Makita vacuum cleaner to your saw, more efficient and cleaner operations can be performed. 13 Securing workpiece · WARNING: It is extremely important to always secure the workpiece properly and tightly with the vise. Failure to do so can cause the tool to be damaged and/or the workpiece to be destroyed. Also, after a cutting operation, DO NOT raise the blade until the blade has come to a complete stop. CAUTION: When cutting long workpieces, use supports that are as high as the top surface level of the turn base. Do not rely solely on the vertical vise and/or horizontal vise to secure the workpiece. Support workpiece over its entire length to avoid blade pinch and possible KICKBACK. 001549 1 2 · 1. Turn base 001796 Vertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assembly (optional accessory). Insert the vise rod into the hole in the guide fence or the holder assembly and tighten the screw to secure the vise rod. Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. If the screw to secure the vise arm contacts the guide fence, install the screw on the opposite side of vise arm. Make sure that no part of the tool contacts the vise when lowering the handle fully and pulling or pushing the carriage all the way. If some part contacts the vise, re-position the vise. Press the workpiece flat against the guide fence and the turn base. Position the workpiece at the desired cutting position and secure it firmly by tightening the vise knob. CAUTION: The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. 1 2 3 6 4 5 1. Vise arm Vise rod Guide fence Holder Holder assembly Vise knob Screw 7 · 14 002247 Holders and holder assembly (optional accessories) The holders and the holder assembly can be installed on either side as a convenient means of supporting workpieces horizontally. Then tighten the screws firmly to secure the holders and the holder assembly. 1 2 1. Holder assembly 002246 2 When cutting long workpieces, use the holder-rod assembly (optional accessory). [. . . ] Magazine/Newspaper From dealer Store display Catalog Other ( ) 2. Construction trade Industrial maintenance Home maintenance Other ( ) 4. Design Features Size Price Makita Brand Power Other ( ) 5. Any comments? Paste Date Purchased Month Day Year 20 Model No. Paste Serial No. Initial Last Name Male Female Single Married Paste Street Address Paste City Province Postal Code Paste AGE: Occupation: Under 19 20-29 30-39 40-49 Over 50 Paste Dealer's Name & Address: 30 Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Certificate of Warranty Mail to Makita Factory Service Centres Head Office: Regional Office: Regional Office: (Montreal) Dartmouth: Ville St. [. . . ]