User manual MAKITA LS1017

[. . . ] Bevel angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Left 45° Max. Cutting capacities (H x W) Bevel angle Miter angle 0° 75 mm x 305 mm (2-15/16" x 12") 0° 90 mm x 240 mm (3-1/2" x 9-1/2") Note 1 40 mm x 305 mm (1-9/16" x 12") 45° (left and right) 75 mm x 215 mm (2-15/16" x 8-1/2") 90 mm x 165 mm (3-1/2" x 6-1/2") Note 2 40 mm x 215 mm (1-9/16" x 8-1/2") 57° (right) 75 mm x 165 mm (2-15/16" x 6-1/2") 90 mm x 125 mm (3-1/2" x 4-7/8") Note 3 - 45° (left) (Note) 1. When using a wood facing 33 mm (1-5/16") thick. When using a wood facing 25 mm (1") thick. [. . . ] Stopper Pin 11 001858 1 3 To remove the blade, use the socket wrench to loosen the hex bolt holding the center cover by turning it counterclockwise. Raise the blade guard and center cover. 2 1. Center cover Socket wrench Hex bolt Blade guard 4 002859 3 2 Press the shaft lock to lock the spindle and use the socket wrench to loosen the hex bolt clockwise. Then remove the hex bolt, outer flange and blade. 1 4 5 1. Blade case Arrow Shaft lock Hex bolt Socket wrench 12 001786 1 2 4 5 To install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surface of the blade matches the direction of the arrow on the blade case. Install the outer flange and hex bolt, and then use the socket wrench to tighten the hex bolt (left-handed) securely counterclockwise while pressing the shaft lock. Return the blade guard and center cover to its original position. Then tighten the hex bolt clockwise to secure the center cover. Lower the handle to make sure that the blade guard moves properly. Make sure shaft lock has released spindle before making cut. 3 1. Hex bolt Outer flange Saw blade Inner flange Spindle 001787 2 1 4 3 1. It consists of two holder assemblies and two rods 12. CAUTION: Always support long workpieces level with the top surface of the turn base for accurate cuts and to prevent dangerous loss of control of the tool. · 1 1. Rod 12 OPERATION · · · CAUTION: Before use, be sure to release the handle from the lowered position by pulling the stopper pin. Make sure the blade is not contacting the workpiece, etc. Do not apply excessive pressure on the handle when cutting. Too much force may result in overload of the motor and/or decreased cutting efficiency. Push down handle with only as much force as is necessary for smooth cutting and without significant decrease in blade speed. Gently press down the handle to perform the cut. If the handle is pressed down with force or if lateral force is applied, the blade will vibrate and leave a mark (saw mark) in the workpiece and the precision of the cut will be impaired. During a slide cut, gently push the carriage toward the guide fence without stopping. If the carriage movement is stopped during the cut, a mark will be left in the workpiece and the precision of the cut will be impaired. · · 15 002177 1. [. . . ] For miters in aluminum, copper, brass, tubing, and other non-ferrous metals. Miter saw blades Combination Crosscutting Fine cross cuts Non-ferrous metals miter saw blades · · · · · · · · · · Vise assembly (Horizontal vise) Vertical vise Socket wrench 13 Holder set Holder assembly Holder rod assembly Set plate Dust bag Triangular rule Lock-off button (2 pcs. ) 28 Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold 29 Your answers to the following questions are appreciated. 1. Hardware/lumber Store Tool Distributor Industrial Supply Other ( ) 3. How did you first learn of Makita Power Tools? [. . . ]