User manual MAKITA LS1030N

[. . . ] Miter Saw Equipped with Electric Blade Brake 255 mm (10") MODEL LS1030N DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w. c o m SPECIFICATIONS Blade diameter : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 mm (10") Hole diameter : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Lower the handle to make sure that the blade guard moves properly. Make sure shaft lock has released spindle before making cut. 3 1. Hex bolt Outer flange Saw blade Inner flange Spindle 001787 2 1 4 3 1. 4. Blade case Arrow Saw blade Arrow 11 001775 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. NOTE: If you connect a Makita vacuum cleaner to your saw, more efficient and cleaner operations can be performed. 2 1 3 1. Fastener Securing workpiece · WARNING: It is extremely important to always secure the workpiece properly and tightly with the vise. Failure to do so can cause the tool to be damaged and/or the workpiece to be destroyed. Also, after a cutting operation, DO NOT raise the blade until the blade has come to a complete stop. 001549 1 2 CAUTION: · When cutting long workpieces, use supports that are as high as the top surface level of the turn base. Do not rely solely on the vertical vise and/or horizontal vise to secure the workpiece. Support workpiece over its entire length to avoid blade pinch and possible KICKBACK. 1. Turn base 12 001796 Vertical vise The vertical vise can be installed on the guide fence or the holder assembly (optional accessory). Insert the vise rod into the hole in the guide fence or the holder assembly and tighten the screw to secure the vise rod. Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. If the screw to secure the vise arm contacts the guide fence, install the screw on the opposite side of vise arm. Make sure that no part of the tool contacts the vise when lowering the handle all the way. If some part contacts the vise, re-position the vise. Press the workpiece flat against the guide fence and the turn base. Position the workpiece at the desired cutting position and secure it firmly by tightening the vise knob. CAUTION: The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. 1 2 3 6 4 5 1. [. . . ] 809 Farmers Branch, TX 75234 (972) 243-1150 12701 Directors Dr. Stafford, TX 77477-3701 (281) 565-8665 3453 IH-35 North, Ste. 101 San Antonio, TX 78219 (210) 228-0676 MASSACHUSETTS 232 Providence Hwy. Westwood, MA 02090 (781) 461-9754 COLORADO 11839 E. [. . . ]