User manual MAKITA LS1212

[. . . ] ENGLISH Slide Compound Saw MODEL LS1212 005263 DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Blade diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 - 305 mm Hole diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25. 4 mm Max. Cutting capacities (H x W) Bevel angle Miter angle 45° (left) 0° * 69 mm x 230 mm 61 mm x 298 mm 55 mm x 310 mm * 69 mm x 162 mm 61 mm x 211 mm 55 mm x 220 mm 0° * 120 mm x 230 mm 107 mm x 298 mm 98 mm x 310 mm * 120 mm x 162 mm 107 mm x 211 mm 98 mm x 220 mm * 120 mm x 115 mm 107 mm x 149 mm 98 mm x 155 mm 45° (right) * 49 mm x 230 mm 40 mm x 298 mm 35 mm x 310 mm * 49 mm x 162 mm 40 mm x 211 mm 35 mm x 220 mm - 45° (left and right) 60° (right) (Note) * mark indicates that a wood facing with the following thickness is used. Miter angle 0° 45° (left and right) 60° (right) Thickness of wood 34 mm 24 mm 17 mm No load speed (min-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 200 Dimensions (L x W x H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 mm x 590 mm x 690 mm Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Then tighten the hex bolt clockwise to secure the center cover. Release the handle from the raised position by pulling the stopper pin. Lower the handle to make sure that the blade guard moves properly. Make sure shaft lock has released spindle before making cut. 3 1. Center cover Hex bolt Socket wrench Blade guard 4 001536 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, insert the dust nozzle into the dust spout on the blade case and fit the bag's entry port over the dust nozzle. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. Fastener If you connect a vacuum cleaner to your saw, more efficient and cleaner operations can be performed. Securing workpiece WARNING: It is extremely important to always secure the workpiece properly and tightly with the vise. Failure to do so can cause the tool to be damaged and/or the workpiece to be destroyed. Also, after a cutting operation, DO NOT raise the blade until the blade has come to a complete stop. · 002260 Sub-fence This tool is equipped with the sub-fence which should ordinarily be positioned as shown in the figure. However, when performing left bevel cuts, set it to the left position as shown in the figure 1 1. Sub-fence 11 002261 1 · CAUTION: When performing left bevel cuts, flip the fence over to the left position as shown in the figure. Otherwise, it will contact the blade or a part of the tool, causing possible serious injury to the operator. 1. Sub-fence 002229 Sub-fence R (optional accessory) The sub-fence R should ordinarily be installed on the right side of the guide fence. Insert the rods of the sub-fence R into the holes in the guide fence. Tighten the screws to secure the sub-fence R. CAUTION: When performing right bevel cuts, never use the sub-fence R. It will contact the blade or some part of the tool, causing a serious injury to operator. 1 · 2 1. Screws 004068 Vertical vise NOTE: When using the holder assembly, install it on the holder as shown in the figure. Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. If the screw to secure the vise arm contacts the guide fence, install the screw on the opposite side of vise arm. [. . . ] If they do not point to 0°, loosen the screws which secure the pointers and adjust them so that they will point to 0°. 3 1. Pointers 001573 (2) 1 2 3 45° bevel angle Adjust the 45° bevel angle only after performing 0° bevel angle adjustment. To adjust left 45° bevel angle, loosen the lever and tilt the blade 45° to the left. Make sure that the pointer on the arm holder points to 45°on the bevel scale on the arm holder. [. . . ]