User manual MAKITA LS1220

[. . . ] Compound Miter Saw Equipped with Electric Blade Brake 305 mm (12") MODEL LS1220 001824 DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Blade diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 mm (12") Hole diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miter angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Left 48°, Right 48° Max. [. . . ] Hex bolt Outer flange Saw blade Ring Inner flange Spindle 001785 2 1 4 3 1. 4. Blade case Arrow Saw balde Arrow 12 001831 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. NOTE: If you connect a Makita vacuum cleaner to your saw, more efficient and cleaner operations can be performed. 1 2 3 1. Fastener Securing workpiece · WARNING: It is extremely important to always secure the workpiece properly and tightly with the vise. Failure to do so can cause the tool to be damaged and/or the workpiece to be destroyed. Also, after a cutting operation, DO NOT raise the blade until the blade has come to a complete stop. CAUTION: When cutting long workpieces, use supports that are as high as the top surface level of the turn base. Do not rely solely on the vertical vise and/or horizontal vise to secure the workpiece. Support workpiece over its entire length to avoid blade pinch and possible KICKBACK. 001549 1 2 · 1. Turn base 001842 Sub-fence This tool is equipped with the sub-fence. It should be positioned as shown in the figure. 1 1. Sub-fence 13 001843 1 · CAUTION: When performing left bevel cuts, flip the fence over to the left position as shown in the figure. Otherwise, it will contact the blade or a part of the tool, causing possible serious injury to the operator. 1. Sub-fence 001796 Vertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assembly (optional accessory). Insert the vise rod into the hole in the guide fence or the holder assembly and tighten the screw to secure the vise rod. Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. If the screw to secure the vise arm contacts the guide fence, install the screw on the opposite side of vise arm. Make sure that no part of the tool contacts the vise when lowering the handle all the way. If some part contacts the vise, re-position the vise. [. . . ] Magazine/Newspaper From dealer Store display Catalog Other ( ) 2. Construction trade Industrial maintenance Home maintenance Other ( ) 4. Design Features Size Price Makita Brand Power Other ( ) 5. Any comments? Paste Date Purchased Month Day Year 20 Model No. Paste Serial No. Initial Last Name Male Female Single Married Paste Street Address Paste City Province Postal Code Paste AGE: Occupation: Under 19 20-29 30-39 40-49 Over 50 Paste Dealer's Name & Address: 30 Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Certificate of Warranty Mail to Makita Factory Service Centres Head Office: Regional Office: Regional Office: (Montreal) Dartmouth: Ville St. [. . . ]