User manual MAKITA LS7504

[. . . ] Bevel angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Left 45° Max. Cutting capacities (H x W) with blade 190 mm (7-1/2") in diameter. Miter angle 0° 45° (left and right) (Note) Bevel angle 0° 50 mm x 182 mm (2" x 7-1/8") 50 mm x 127 mm (2" x 5") 45° (left) 35 mm x 182 mm (1-3/8" x 7-1/8") 35 mm x 127 mm (1-3/8" x 5") The max. Cutting capacities may vary according to workpiece, blade and/or charging condition. No load speed (RPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Stopper arm 12 002197 1 Adjusting the miter angle Loosen the grip by turning counterclockwise. Turn the turn base while pressing down the lock lever. When you have moved the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise. CAUTION: When turning the turn base, be sure to raise the handle fully. After changing the miter angle, always secure the turn base by tightening the grip firmly. 5 4 1. 5. 2 3 Turn base Miter scale Pointer Grip Lock lever · · 002198 Adjusting the bevel angle To adjust the bevel angle, loosen the lever at the rear of the tool counterclockwise. Push the handle to the left to tilt the saw blade until the pointer points to the desired angle on the bevel scale. Then tighten the lever clockwise firmly to secure the arm. 1 1. Lever · 002199 CAUTION: When tilting the saw blade, be sure to raise the handle fully. After changing the bevel angle, always secure the arm by tightening the lever clockwise. When changing bevel angles, be sure to position the kerf boards appropriately as explained in the "Positioning kerf boards" section. · 1 · 3 2 1. Raise the blade guard and center cover. 4 3 Blade Case Hex bolt Socket wrench Blade guard 1. Shaft lock Arrow Blade case Socket wrench Hex bolt 001771 Press the shaft lock to lock the spindle and use the socket wrench to loosen the hex bolt clockwise. Then remove the hex bolt, outer flange and blade. 1 2 3 5 1. Outer flange Inner flange Spindle Saw blade Hex bolt 4 To install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surface of the blade matches the direction of the arrow on the blade case. Install the outer flange and hex bolt, and then use the socket wrench to tighten the hex bolt (left-handed) securely counterclockwise while pressing the shaft lock. Return the blade guard and center cover to its original position. Then tighten the hex bolt clockwise to secure the center cover. Release the handle from the raised position by pulling the stopper pin. Lower the handle to make sure that the blade guard moves properly. Make sure shaft lock has released spindle before making cut. 001783 2 1 4 3 1. 4. Arrow Blade case Saw blade Arrow 16 002217 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy. [. . . ] Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center. · Carbide-tipped saw blades For smooth and precise cutting in various materials. Miter saw blades · · · · · · · · · · · Vise assembly (Horizontal vise) Vertical vise Socket wrench 10 Holder set Holder assembly Holder rod assembly Set plate Dust bag Triangular rule Lock-off button (2 pcs. ) Various type of Makita genuine batteries and chargers. 31 Memo 32 Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitby, Ontario L1N 7B7 Fold 33 Your answers to the following questions are appreciated. 1. Hardware/lumber Store Tool Distributor Industrial Supply Other ( ) 3. [. . . ]