Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA PC8114. We hope that this MAKITA PC8114 user guide will be useful to you.
Lastmanuals help download the user guide MAKITA PC8114.
Detailed instructions for use are in the User's Guide.
[. . . ] It can be tightened up by pulling the lever again. b
4
Adjust support plate , aligning notches. Now tighten nuts firmly, as shown in figure B. [. . . ] Now tighten nuts firmly, as shown in figure B. C
12 11
13 8 7
Thread cable (7), as shown in picture, through the adapter bracket (8), the compression spring (9), the gas operating device (10) and the Bowden cable sleeve (11). Thread cable end through the gas lever (12) and pull on the cable end until the cable has been completely threaded through and the Bowden cable sleeve (11) is resting in the support of the gas lever (12). Press Bowden cable sleeve into the support (13) on the control shaft. NOTE: Only tighten the clamping screw on the gas lever (12) slightly to prevent the cable slipping out again. The gas lever is set correctly when the power cut is mounted (see “Mounting the power cut”). 9
D
6
11 10
14
15
Mount the clamp bracket (14) from underneath (see circled diagram) against the support plate (17) using screws (16). 16 17
E
Mounting the guide wheel
Push screw (1) through the rectangular hole on the guide trolley (2) (align the sides of the screw with the sides of the hole). mount tank holder (3) and control shaft (2) with star handle (see picture). 1
3
H
4
Press the power cut between the two supports (4) onto the support plate. Fold out (I) the holding brackets (5) and secure (II) using the eccentric plate (6). Lock the eccentric plate in place using the quick-action lever (7). I 5 6
II
I
7
1
2
4
5
Setting the gas lever
Turn the gas lever (1) back as far as it will go (parallel to the control shaft). 3
2 - 3 mm
Take hold of cable end (3) and pull until the distance between the gas operating device (5) and the gas lever on the power cut (4) is about 2-3 mm. J
3 2
Adjusting the cutting line
If the guide trolley pulls to the left or right of the straight cutting line when you are cutting with the power cut, this can be corrected by pushing aside the support plate (1). Pushing the support plate (1) in the direction A corrects cutting to the left. [. . . ] 3
2 - 3 mm
Take hold of cable end (3) and pull until the distance between the gas operating device (5) and the gas lever on the power cut (4) is about 2-3 mm. J
3 2
Adjusting the cutting line
If the guide trolley pulls to the left or right of the straight cutting line when you are cutting with the power cut, this can be corrected by pushing aside the support plate (1). Pushing the support plate (1) in the direction A corrects cutting to the left. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA PC8114
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA PC8114 will begin.
