User manual MARANTZ CDR300

[. . . ] Model CDR300 User Guide CD Recorder R CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT I. H. T. IEC 825 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. LASER SAFETY This unit employs lasers. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury. CAUTION USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. [. . . ] (external) when an external RC-5 remote control system is used. Notes: · Switch to INT. (internal) to enable the supplied IR (infrared) remote. AUX IN R 3 AUX IN jacks Plug Right and Left RCA audio cables in here to connect to the output of an external unit. Use for recording onto the CDR drive from an external audio source such as a cassette deck, or CD player. 7 FOOT PEDAL jack FOOT PEDAL L An optional foot pedal can provide Play/Pause control for the CDR drive. This jack does not perform pause or continue during recording. Foot pedal (FT200) is available from Superscope Technologies at (630) 820-4800 or www. superscope-marantzpro. com. 8 Power plug Plug one end of the supplied power cord in here and the other into an AC outlet. - 15 - Controls, Connections (rear) continued 9 10 MIX OUT R LINE OUT AUX IN R IN DIGITAL REMOTE RC-5 EXT. INT. Push and release the SELECT control. Turn the SELECT control to choose between Lead Acid and NiCd/NiMH. L dB-50 -30 -22 -16 -12 -8 -4 0 TOTAL TRACK IN FOOT PEDAL OUT OUT DC IN POWER ON OFF R CD L L L dB-50 -30 -22 -16 -12 -8 -4 0 TOTAL TRACK R CD DC IN 9 DC IN When correct push and release MENU/STORE. The CDR300 can be powered by a Lead Acid, NiCd, or NiMH battery power supply. A Lead Acid power supply is available from Superscope Technologies (630) 820-4800 or www. superscope-marantzpro. com. How to use a DC power supply Always begin recording sessions with a fully charged battery regardless of battery type. Plug the DC power supply into DC IN (9). Turn power on with the Standby POWER slide switch on the top of the unit. Battery life depends on use and battery type. When the CDR300 detects a low battery condition during recording the red STANDBY light flashes and the display alternates between PRESS STOP and LOW BATTERY. L dB-50 -30 -22 -16 -12 -8 -4 0 DC IN pin out 1 DC IN 2 3 4 1 2 3 4 12VDC not used not used 12VDC + L dB-50 -30 -22 -16 -12 -8 -4 0 TOTAL TRACK R TOTAL TRACK R CD-RW CD-R CD-RW CD-R POWER ON OFF 10 Power switch Push and release to turn power ON (in position). Push and release to turn power OFF (out position). Normally, to retain memory, leave this switch at ON and turn power on and off with the Standby POWER slide switch on the top of the unit. Stop recording as soon as possible. When you stop recording the temporary TOC will automatically be updated so your recording is not lost. After two minutes of LOW BATTERY the CDR300 will stop recording and will automatically update the temporary TOC. Battery Backup When both AC and DC power supplies are connected the DC supply serves as a battery backup when AC power is interrupted. BATTERY SELECT A DC power supply with Lead Acid, NiCd, or NiMH batteries can be used, but batteries differ in electrical characteristics. With the CDR300 at Stop push and release the MENU/STORE button. Turn the SELECT control so BATTERY SELECT is displayed. L dB-50 -30 -22 -16 -12 -8 -4 0 TOTAL TRACK R CD - 16 - How to Play How to Play a CD (basics) 1 Connect and turn on the CDR300, see Connections (basic) on page 7. ERASE FINALIZE How to play ERASE FINALIZE BASS MID TREBLE REC TEXT PHANTOM PROG REPEAT MENU/STORE DISP REC MODE SINGLE A-B CANCEL/DELETE CD RECORDER CDR300 PROFESSIONAL SELECT ERASE FINALIZE REC POWER STANDBY BASS MID TREBLE REC PUSH ENTER TEXT PHANTOM PROG REPEAT MENU/STORE DISP REC MODE SINGLE A-B CANCEL/DELETE 1 CD RECORDER CDR300 SELECT ERASE FINALIZE REC PUSH ENTER 2 3b PROFESSIONAL POWER STANDBY 3 INPUT MIC/LINE PHONE/SPEAKER PHONE SELECTOR LINE OUT LEVEL AUX MIC/LINE MIX OUT MIC LINE INT ANALOG DIGITAL How to Pause Push and release the Play/Pause button (1) to Pause. When paused, push and release to continue play from the same point. REC LEVEL MANUAL ALC LIMITER MIC/LINE ATT OFF ON SPEAKER OFF ON OPEN/CLOSE L L/R L+R R PUSH PUSH PHONES LINE OUT Recordable ReWritable CD PLAY / RECORD How to Stop Push and release the Stop button (2) to Stop. When Play/Pause is next pushed, play starts from the beginning of the disc. LEFT MIC/LINE RIGHT d e 2 2 Push and release the OPEN/CLOSE switch to open the CDR drive. Insert your CD and push OPEN/CLOSE to close the CDR drive. [. . . ] · Always keep the tray closed to avoid dust on the lens. - 35 - Limited Warranty: Your Marantz Professional product is warranted against manufacturer defects in material and workmanship for a period of one year parts and labor. Except as specified below this warranty covers defects in material and workmanship. The following are not covered under warranty: 1. Damage, deterioration, malfunction or failure to meet performance specifications resulting from: Accidents, acts of nature, misuse, abuse, neglect or unauthorized product modification. [. . . ]