User manual MARANTZ MT8600

[. . . ] Do not install the projector in a location subject to high levels of dust or humidity. Dust accumulating inside the projector could cause a short circuit that in turn could cause a fire or electric shock. 4. Use only the parts provided with the bracket, and any other parts (commercially available) that are specified in this manual. Using other parts could cause the projector to fall and injure someone. 12. Do not install the projector in a location that is exposed to direct sunlight or in a location that is subject to extreme fluctuations in temperature (such as near an air conditioner). Such conditions can cause the projector housing to warp or to become discoloured. 5. Do not modify the bracket or the parts provided with the bracket. Modifying the bracket or the other parts could cause the projector to fall and injure someone. 13. Do not wipe the exterior of the ceiling mount with benzene, paint thinner or cleaning compounds. Doing so could damage the finish. 6. Do not use damaged parts. Using damaged parts could cause the projector to fall and injure someone. [. . . ] Use only the parts provided with the mount, along with any parts (commercially available) that are specified in this manual. Do not modify the mount or the parts provided with the mount. if any parts become damaged, contact your dealer. All bolts and screws must be tightened securely. Make sure not to block any ventilation openings when installing the projector. Special techniques and experience are required when installing the projector with this mount. Contact your dealer to install the projector for you. Once the projector is installed, safety checks should be conducted on a regular basis. MT8600 INSTALLATION INSTRUCTIONS PROJECTOR MOUNT Step 1 Base Plate Connectors #1 and Projector Mount Ceiling Plate 1 with ceiling mounting holes #2. Figure 1 1 4 Ceiling Wire Access 4 14" 2 3 2 8 5/8" 3 2 Plate 1 Insert Base Plate connectors #1 into the lateral positioning slots #3 as shown in #4 from the underside of Plate 1. The lateral positioning slots will give you 2 1/4" inches of lateral adjustment for projector alignment. Base Plate Connectors #1 Projector Mount Ceiling Plate 1 The ceiling should be capable of supporting a weight of at least five (5) times the projector(s) weight. If it cannot, the ceiling must be reinforced. Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury. Warning Step 2 Horizontal Adjustment Plate 2 (Base Plate Connector Holes #3). Figure 2 3 Wire Access 3 10 5/8" Hardware List 1. Four (4) 3/8 (inch) nuts Fourteen (14) 3/8 (inch) flat washers Four (4) 8 (mm) screws Twelve (12) 1/4" screws Two (2) 1" rubber washers Two (2) 1" flat washers 7. One (1) Ceiling Mount #1 Two (2) Base Plate Connectors One (1) Horizontal Tilt Plate #2 One (1) Horizontal Tilt Plate #3 One (1) Projector Plate #4 3 3 Adjustment Ranges and Load Allowances Horizontal Tilt (yaw) Vertical Tilt (tilt) Rotation Lateral Shift Maximum Load Allowance +/+/+/+/10 degrees 20 degrees 15 degrees 21/4 inches 32 Lbs. 7 5/8" Plate 2 Base plate connector holes #3 provide 15 degrees of horizontal rotation adjustment. Attach horizontal adjustment Plate 2 to projector mount ceiling Plate 1 using the four (4) 3/8" (inch) nuts and washers provided. MOUNT MT8600 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued Step 2 B Horizontal Adjustment Plate 2 (Figure 2) attached to Projector Mount Ceiling Plate 1. Figure 3 Step 3 B Horizontal Tilting Plate 3 Attached to Plates 1 and 2. [. . . ] screws provided. continued over MOUNT MT8600 PROJECTOR MOUNT Step 4 B Projector Mounting Plate 4 (continued) Figure 7 CEILING Mount Side INSTALLATION INSTRUCTIONS continued Projector Mounting Plate 4 connected to Mounting Plate 3 Figure 8 Mounts Fully Assembled Ceiling Side 200 Tilt 200 Tilt Projector Side Projector Side Plate 4 Work in a group of 2 or more to carry the projector and follow manufacturer's guidelines for relocating as stated in the VP8600 owner's manual. Lift and slide the projector onto the 1/4in. screws previously installed in the metal studs of the plate on the ceiling (see arrow in Figure 7). [. . . ]