User manual MARANTZ PD4298HD

[. . . ] Slim Line Plasma Monitor PD4298HD USER MANUAL MANUEL UTILISATEUR MANUAL DE USUARIO READ THE INSTRUCTIONS INSIDE CAREFULLY. KEEP THIS USER MANUAL FOR FUTURE REFERENCE. For future reference, record the serial number of your monitor. SERIAL NO. The serial number is located on the rear of the monitor. NOTE: The information in this manual is subject to change without notice. The manufacturer assumes no responsibility for any errors that may appear in this manual. [. . . ] 6) Turn on the monitor, then the PC to make sure that a display image appears on the monitor screen. s For instructions on turning on the monitor and adjusting its display images, see "Operating Instructions" ( 9 to 17 ). Monitor rear panel PC To audio output terminal To signal output terminal To signal output terminal Power cable Power cable connector AUDIO IN To audio input terminals RGB1 D-SUB IN RGB2 L/MONO R V H B G R RS232C IN Nearer Terminal Further Terminal To signal input terminals To signal input terminals (such as a Laser Disc player, a DVD player, a DSS, or a Video Camera) q Read SAFTEY GUIDELINES ( to ) carefully to ensure maximum safety before proceeding to these steps: 1) Choose an appropriate site and install the product on a level table where the stand is secure. s Install the monitor to have ready access to a power socket available. 2) Make sure that the video equipment's power switch is off. 3) Interconnect the signal input terminal on the monitor rear panel and the video equipment's signal output terminal to each other using an optional cable. 4) Insert one end of the power cable included into the rear-panel power cable connector and the other end into a power socket. 5) Turn on the monitor, then the video equipment's to make sure that a display image appears on the monitor screen. s For instructions on turning on the monitor and adjusting its display images, see "Operating Instructions" ( 9 to 17 ). Monitor rear panel Video equipment (such as a Laser Disc player, a DVD player, a DSS, or a Video Camera) Power cable Power cable connector AUDIO IN SPEAKER TERMINAL (88W) VIDEO2 L/MONO R + + VIDEO1 COMPOSITE IN Nearer Terminal White (W) Further terminal Red (R) COMPONENT IN PR/CR PB/CB Y VIDEO S R L Yellow (V) Use if the video equipment has an S video input terminal To component input terminals s If video equipment with an S video output terminal is used, cabling by the S video cable is recommended to provide finer video quality. (If an S video input terminal and a video input terminal connect to the monitor at the same time, S video input would govern. ) 7 ENGLISH Connecting to Video Equipment To S video output terminals To component output terminals To audio/video output terminals To audio output terminals Yellow(V) Red(R) White(W) White(W) Red(R) W e hit ) (W To S video input terminals d Re (R) To audio input To audio/ video input terminals terminals INSTALLATION INSTRUCTIONS (continued) Handling the Remote Controller Loading Batteries The life of the batteries used with the remote control unit is about 6 months with normal use. Also be sure to replace batteries earlier when you notice that they are getting weak. Do not use alkaline, manganese, nickel-cadmium (Ni-Cd) or other different types of batteries together. 2) Insert the new batteries (AA type) with correct (+) and (-) polarity. 3) Close until it clicks. ENGLISH 8 Handling the Remote Controller q Use the remote controller within about 15 feet from front of the unit's remote-control receiver and within 30 degrees on both sides. With in 30 degrees POWER SOURCE With in 30 degrees About 15 feet ON ON/OFF OFF LEARNING REMOTE CONTROLLER RC1200 MACRO MODE ENT ENT CH OK VOL CD DVD CD-R/MD DSS TV VCR AUX LD TUNER TAPE AMP CLEAR AUTO MEMO DOLBY THX GUIDE DTX MUTE HALL 1 MATRIX 2 MOVIE 3 2CH 4 OSD 5 SLEEP 6 7 8 9 0 Do not use new and old batteries together. The batteries could explode or leak, resulting in fires, physical injury, or stains. CAUTIONS s When loading batteries, observe their correct polarities as marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains. s TIPS Do not drop or impact the remote controller. Do not splash the remote controller with water or put it on a wet object to avoid possible failures. s Before leaving the remote controller out of use for an extended period of time, remove the batteries from it. s If the remote controller begins to lack responsiveness, replace the batteries. s Strong light such as direct sunlight impinging on the photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light. s s OPERATING INSTRUCTIONS Turning Power On and Off unit to ON and then press the SUB POWER button or the POWER ON or POWER SOURCE ON/OFF button of the remote controller. q To turn off the main unit power supply, press the SUB POWER button of the main unit or the POWER OFF or POWER SOURCE ON/OFF button of the remote controller, then main unit the MAIN POWER switch ( ) to OFF. s For normal operations, leave the MAIN POWER switch ( ) main unit to ON and use the SUB POWER button or the POWER ON or POWER SOURCE ON/OFF button of the remote controller to turn the power on and off. Indicating lamp Off Power status Off Operating When the MAIN POWER switch set to OFF. is Lights red Off (standby) When the MAIN POWER switch is set to ON and POWER OFF or POWER SOURCE ON/OFF button of the remote controller or the SUB POWER button on the main unit located at the front part of the bottom plate is off. When the MAIN POWER switch is set to ON and POWER ON or POWER SOURCE ON/OFF button of the remote controller or the sub power button on the main unit located at the front part of the bottom plate is on. Lights or blinks green On When the indicating lamp blinks in green or the message "POWER SAVE" or "OUT OF FREQUENCY" appears on the screen, there is something unusual about the status of reception. [. . . ] The display image appears flowing (display 2) (RGB input). Display 1 V e r t i c a le f o r e a d j u s t m e n t B s t r e a kS o m e c h a r a c t e r s s a r e b lu r r e d . ABCDEFGHIJ abcdefgABCDEFGabcd ABCDEFGHIJ abcdefgABCDEFGabcd ENGLISH 24 B ABC Example ABC ABC ABC A fte r a d ju s tm e n tA fte r a d ju s tm e n t A l l c h a r a c t e r s a p A le a r a r a c t e r s a r e p l ch c r is p n o w . Adjust 25 . 1) Either turn the remote controller jog dial to choose MENU and press the ENT button or press the main unit MENU button to open the adjustment menu. 2) Press CURSOR/CONTROL button several times to choose DISPLAY. [. . . ]