User manual MARANTZ PM-90SE

[. . . ] Your purchase receipt or invoice is adequate for such proof. ONLY This undertaking is in addition to a consumer's statutory rights and does not affect those rights in any way. ITALIANO GARANZIA L'apparecchio è coperto da una garanzia di buon funzionamento della durata di un anno, o del periodo previsto dalla legge, a partire dalla data di acquisto comprovata da un documento attestante il nominativo del Rivenditore e la data di vendita. La garanzia sarà prestata con la sostituzione o la riparazione gratuita delle parti difettose. Non sono coperti da garanzia difetti derivanti da uso improprio, errata installazione, manutenzione effettuata da personale non autorizzato o, comunque, da circostanze che non possano riferirsi a difetti di funzionamento dell'apparecchio. [. . . ] When MC is set, the center of the button is lit a blue color. Set the phono equalizer amplifier according to the type of cartridge you use. Turn the VOLUME knob on the PM-90SE to the right or press the VOLUME 3 button on the remote controller. !4 Side Illumination The side illumination casts a blue light over switches and buttons. It can be turned ON and OFF from the DISPLAY button. For instructions on how to operate the side illumination, see "HOW TO OPERATE THE SIDE ILLUMINATION" on pg. 0. 5 dB steps Turn the VOLUME knob on the PM-90SE to the left or press the VOLUME 4 button on the remote controller. DISPLAY Min The display panel also displays left-right level balance and tone control trimming level. For instructions on how to adjust bass and treble, see "How to Trim Bass" and "How to Trim Treble" on pg. The display panel also displays messages in response to PM-90SE operation. OPERATE !7 OPERATE Indicator This indicator indicates the operating status of the PM11S1. When the ID is set to "0" for standalone operation, it is lit a red color. When multiple PM-90SEs are connected by FCBS, only the OPERATE indicator of the master PM11S1 (ID 1) lights a red color. Slave PM-90SEs whose OPERATE indicator does not light a red color cannot be used to operate other units in sync. In the bi-amp mode, the R channel jack cannot be used. G RECORDER 1/2 OUT Jacks These jacks are for connecting to the recording input jacks of a CD-R, MD deck, tape deck, etc. Output signals can be turned ON/OFF from the REC OUT button on the front panel. In the bi-amp mode, the signals input to the L channel are output to both output jacks. L AC IN Socket Connect one end of the included power cable here and the other end to a power outlet. The PM-90SE can be powered by 230V AC only. 12 NAMES AND FUNCTIONS OF PARTS RC-11PMS1 REMOTE CONTROLLER This remote controller can control the PM-90SE and Marantz Super Audio CD players and DVD players that have a remote control receptor. The operations possible by remote control may differ with each component, therefore see the instruction manual that came with the component. Remote controller buttons are laid out as shown below. z Input Selector Buttons These buttons are for selecting the input source to use in playback. x TRIM Button This button starts trimming. When multiple PM-90SEs are connected by FCBS, this button selects the amplifier with which to perform trimming. c EXIT Button OPEN/ CLOSE SOUND MODE This button ends the trimming mode when trimming is finished. v TONE Button PHONO BALANCED CD This button turns tone (bass /treble) control ON and OFF. RECORDER 1 LINE 1 RECORDER 2 LINE 2 b ATT Button This button attenuates volume level with one press. TRIM EXIT TONE + n Volume Buttons L R ENTER 3 : This button increases the volume level. 4 : This button decreases the volume level. ATT DISPLAY - m DISPLAY Button This button turns the display ON and OFF. VOLUME , Cursor Buttons In the Trimming Mode These buttons are for selecting the channel to trim and the trimming level. ENTER: This button selects the trim mode (LEVEL. 2 /R : This button selects the R channel for trimming. 1 /L : This button selects the L channel for trimming. [. . . ] 5Hz ~ 120kHz±3dB Dumping factor (8 load, 20Hz ­ 20kHz) . . . . . . . . . . . . . . . . . . . . . . . 100 Input sensitivity/Input impedance PHONO (MC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270µV/100 PHONO (MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3mV/47k BALANCED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]