User manual MARANTZ PM4001

[. . . ] Model PM4001/PM4001OSE User Guide Integrated Amplifier ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] To ensure proper heat radiatizN, ensure the below clearance from walls and other equipment. í Accessories check Before use, check the below accessories were included in the package. · Remote control unit (RC4001PM) · Size "AA" batteries x 2 Left 0. 2 m or more Above 0. 2 m or more Right 0. 2 m or more Rear 0. 2 m or more · User Guide · Registration Card í Keep objects off Keep objects off the PM4001. Blocking the vent can result in accident and damage. 1 Turntable Tuner MD or Tape deck etc. OUTPUT OUTPUT INPUT OUTPUT OUTPUT OUTPUT INPUT CD player Analog output jacks of DVD player, AV components, video disc player, etc. CD recorder etc. S PE AK ER S YS TEM S SY STE M 1 : 4 - 1 6 OH M S SY STE M 2 : 4 - 1 6 OH M S SY STE M 1+ 2 : 8 - 16 OH M S SYSTEM1 R L R L SYSTEM2 2 ENGLISH CONNECTIONS CONNECTIONS CONNECTION OF TUNER Connect the output jacks of your stereo tuner to the TUNER jacks of this unit. CONNECTION OF COMPACT DISC PLAYER Connect the output jacks of your CD player to the CD jacks of this unit. CONNECTION OF TURNTABLE Connect the L (Left) output cord of the turntable to the "L" PHONO jack of this unit, and connect the R (Right) output cord to the "R" PHONO jack. Also be sure to connect the turntable's grounding wire to the GND jack of this unit. The GND jack does not have to be connected if the turntable is not provided with a grounding wire. The cartridge of the connected turntable should be of the MM type. To use a turntable with an MC type cartridge, it is required to use a step-up transformer. Connect the IN (recording input) jacks of the MD or tape deck to the RECORDER 2 OUT jacks of this unit, and connect the OUT (playback output) jacks of the MD or tape deck to the RECORDER 2 IN jacks of this unit. Connect the IN (recording input) jacks of the CD recorder to the RECORDER 1 OUT jacks of this unit, and connect the OUT (playback output) jacks of the CD recorder to the RECORDER 1 IN jacks of this unit. CONNECTION OF SPEAKER SYSTEMS This unit is equipped with two sets of SPEAKER SYSTEM terminals­­SYSTEM 1 terminals and SYSTEM 2 terminals. Usually connect your speaker system to the SYSTEM 1 terminals. · The speakers in the speaker system should have an impedance between 8 and 16 ohms. If speakers with an impedance of less than 8 ohms are connected, the protection circuitry may be activated during play. · Connect the Right channel speaker to the R terminals, and the Left channel speaker to the L terminals. · The output terminals have positive (+: Red) and negative (­: Black) polarity, and each speaker also has the same polarity (+ and ­). When connecting the speaker, be sure to connect the terminals with the same polarity (+ with +, ­ with ­). ENGLISH WIRING SPEAKER CABLE · Be careful not to short circuit in wiring speaker cables. · Peel off the corting of speaker cable as shown below. Approx. 1 cm Cut the corting of cable. Peel off the edge of cable. Twist conductors. · Wiring with speaker cable. Turn counter-clockwise to loosen. Insert conductor of cable. Turn clockwise to tighten. 3 FRONT PANEL q w e r t y u !4 q POWER SWITCH !3 !2 !1 !0 o i i LOUDNESS SWITCH The LOUDNESS switch compensates for human hearing characteristics by boosting the bass and treble response at low volume levels to achieve a more pleasing tonal balance. Pressing once switches the power ON, and pressing again switches it OFF. If the POWER switch is in the ON position, the power of this unit can be turned ON/OFF by pressing the POWER button on the remote control unit. o SPEAKERS 1 / 2 SWITCHES These switches are used to select the speaker system(s) connected to the SPEAKER SYSTEM 1 / 2 terminals on the rear panel. If both the 1 and 2 switches are pressed to the low positions, two speaker systems can be used at the same time. [. . . ] · wipe the equipment with the damp cloth. · dry the equipment by wiping it with a dry cloth. 8 ENGLISH TROUBLESHOOTING SPECIFICATIONS & DIMENSIONAL DRAWINGS Power output RMS 8 Ohms / 4 Ohms (40 Hz ­ 20 kHz) . . . . . . . . . . . . . 40 / 55 W DIN 8 Ohms / 4 Ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 / 60 W IHF dynamic power 8 Ohms / 4 Ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]