User manual MARANTZ PMD351

[. . . ] Model PMD351 User Guide Combination Stereo Cassette Deck/CD Player CLASS 1 LASER PRODUCT LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. LASER SAFETY This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device due to possible eye injury. CAUTION : USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. -2- ENGLISH WARNINGS CAUTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. [. . . ] Set the Dolby Noise Reduction control switch to the same position as the tape was originally recorded in (i. e. tapes recorded with Dolby B noise reduction need to have this switch in the Dolby B position, tapes recorded with Dolby C noise reduction need to have this switch in the Dolby C position, and tapes recorded without Dolby Noise Reduction need to have this control set to the Off position). Set the reverse mode control switch to the desired position. Press the play control button to begin play- E F G H back in the forward direction. Press the play control button to begin playback in the reverse play direction. When the tape enters into the playback mode, the indicator on the play control button will change from the flashing mode to a constant on mode to indicate playback is operating. Pressing the stop control button will stop the tape transport during playback. - 12 - ENGLISH TAPE REWIND/FAST FORWARD Regardless of the direction that the tape transport is currently in, pressing the (Fast Forward) control button will place the tape transport in the high speed fast forward mode and the tape will advance quickly (Rewind) control from left to right. Pressing the button will place the tape transport in the high speed rewind mode and the tape will retract quickly from right to left. In either the fast forward or the rewind mode, the tape transport will continue to fast forward or rewind until the stop control button is pressed or the end of the tape is reached. Note: Automatic search operations cannot operate on the Tape and CD at the same time. 8. To pause the tape transport during recording, press the REC/PAUSE button. Pressing the STOP button rewind button in the will stop the tape transport during recording. Pressing the play/record direction or the fast forward button in the play/record direction will cause the unit to return to the position at which recording began. TAPE RECORD 1. Open the cassette holder by pressing the EJECT button. Load a recordable cassette tape into the cassette holder and close. The indicator on the play control button will begin to flash. (If you wish to change the tape direction, press the play control button and then press the stop control button). Set the DOLBY NR switch to the position that you want to record the tapes' noise reduction in (i. e. tapes to be recorded with Dolby B noise reduction need to have this switch in the Dolby B position, tapes to be recorded with Dolby C noise reduction need to have this switch in the Dolby C position, and tapes to be recorded without Dolby Noise Reduction need to have this control set to the Off position). When recording FM broadcast with Dolby Noise reduction on, set the MPX FILTER switch (on the back of the unit) to the On position. Set the REVERSE MODE switch to the desired position. Set the ALC control to the desired position, on or off. [. . . ] Except as specified below, this warranty covers defects in material and workmanship. The following are not covered under warranty: 1. Damage, deterioration, malfunction or failure to meet performance specifications resulting from: a) Accidents, acts of nature, misuse, abuse, neglect or unauthorized product modification. b) Improper installation, removal or maintenance, or failure to follow supplied instructions. [. . . ]