User manual MARANTZ RC101E

[. . . ] Model RC101 User Guide Remote Controller NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The preset codes are TV, DVD, CD and DSS. Settings can be made in one of two ways. When the preset codes are set, the following codes are contained in the source button of the remote controller. See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings. Remote control source name TV DVD CD DSS Corresponding preset code TV DVD CD SATELLITE Device name Television DVD player CD player Satellite broadcasting tuner equipment SCANNING THE CODE TABLE Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. 3. 2. 5. 2. Switch on the appliance which should be controlled. Press and hold down the SOURCE button for appliance which should be controlled and press SET button until the SEND indicator blinking twice. Aim the remote controller at the appliance and alternately press the CH+ and SOURCE ON buttons slowly. 3. 7 ENGLISH BASIC OPERATION Importants: • Some codes may be not match your equipment. In this case, you can use LEARN mode to store these codes. • The preset codes do not cover full functions. If you need extra function, use LEARN mode to store extra function. • When the batteries are getting weak, the preset procedure is not successful. 4. 5. Stop when the appliance turns off. RESETTING THE CODE LEARN MODE This remote controller is capable of learning and storing codes used by other remote controls that you already own. For codes which are not learned, the remote controller will transmit either the Marantz preset codes from the initial settings, or remote codes from another manufacturer’s AV equipment which is set by the customer. The receiver sensor for the remote control signals is located at the top of the remote controller. Notes: • This remote controller is capable to learn around 60 codes. • When the batteries are getting weak , the learing procedure is not successful. 4. Select the button to be learned. When the following key learned • SOURCE buttons The learning function is unavailable for all SOURCE buttons in any mode. • POWER ON button • POWER OFF button • VOL +/- button • MUTE button • INFO button • SLEEP button The above keys are common use in each device mode. It can be learned in TV mode. ERASING PROGRAMMED CODES (RETURNING TO INITIAL SETTINGS) Codes can be erased in three ways: by buttons, sources, and by all memory contents. Erasing the code by buttons 3. Press ENTER button to continue erasing. • The SEND indicator blinks twice and the mode returns to LEARN mode. [. . . ] 2005, 2009, 2020, 2035, 2057 Sampo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2008, 2012, 2022, 2024, 2027 Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2050, 2052 Sharp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2044, 2045 Sherwood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2051 Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2001, 2013, 2059 Toshiba . . . . . . . . . . . . . . . . . . . . . . 2004, 2008, 2026, 2028 Yamaha . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2046, 2060 Zenith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]