User manual MARANTZ RC2001

[. . . ] Model RC2001 User Guide Remote Controller RC2001_E_cover. indd 3 07. 10. 11 1:03:12 PM NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] • This is a convenient function for devices that do not have a sleep timer or for setting the sleep timer using multiple devices. • The RC2001 performs regular operation even when the sleep timer is activated. ENGLISH 1. Press the button that will be assigned to the sleep timer. Each time the button is pressed, the sleep setting time changes in the cycle shown below. PROCEED?SLEEP 30 SLEEP OFF SLEEP 60 SLEEP 90 SLEEP 120 1. 4. Press the Home button to enter Home mode for the RC2001. Select the devices that are set in Home mode. Perform operation of the device that you want to control in the selected device mode. To control another device, return to Home mode and select another device. 2. 3. The preinstalled default user file is used to control Marantz products. The AV receiver device input switching code is assigned to the button next to the displayed device name of the device mode. Example: After DVD mode is selected in the remote controller, pressing the button next to DVD, shown in the first column in the LCD, transmits the AV receiver DVD input command. When the time that you want to set is displayed, wait at the setting for three seconds. • The sleep setting screen is no longer displayed on the LCD, and the sleep timer is automatically started. And the sleep timer icon is displayed in Sub Info area of the LCD. • When the remaining time for the sleep timer setting is 10 minutes, the remaining time is displayed in the Sub info. area of the LCD. DVD input command for Marantz AV Receiver. SLEEP TIMER icon 6 RC2001_E_01_ENG. indd 6 07. 10. 11 0:59:12 PM MAIN MENU The various settings for the remote device are made in the main menu. 1. Place the remote controller so that its infrared signal transmitter is facing the infrared signal receiver on the Marantz remote controller at a distance of about 2 inches (0. 05 m). ENTERING THE MAIN MENU 1. 2. Press the Home button to enter Home mode for the RC2001. Hold down the Home button and Menu button at the same time for three seconds to display MAIN MENU on the LCD. 2. Display the MAIN MENU on the LCD of the RC2001, and then press the button next to the LEARNING indicator. 3. The screen appears as shown below. Pressing the button next to the CHECK indicator on the LCD displays the timer settings. 2. 2. Use the numeric buttons (0 to 9) and cursor buttons (t and u) to set the time for the timer. After making the setting, press the ENTER button. When the LCD appears as shown below, the timer has not been set. • Either press the ENTER button or wait three seconds for the LCD to automatically return to the TIMER menu. • Pressing the Home button from the TIMER MENU screen returns the LCD to the MAIN MENU. 9 RC2001_E_01_ENG. indd 9 07. 10. 11 0:59:13 PM ENGLISH 2. TIMER OPERATION SETTINGS 3. Home mode is shown in the LCD. Select the commands and devices for the commands that will be sent by timer programming. • If a command assigned to the HARD button is to be sent by timer programming, press the HARD button when selecting the command to make the setting. [. . . ] • TIMER SETUP • BACK LIGHT TIMER • LCD • BEEP 16 RC2001_E_01_ENG. indd 16 07. 10. 11 0:59:15 PM This displays the settings made in the MAIN MENU and the status of the remote device. CHECKING THE STATUS If the RC2001 is not operating properly, use the procedure below to perform a reset (restart). Performing a reset does not erase the settings in the RC2001. 1. Display the MAIN MENU on the LCD of the RC2001, then press the button next to the STATUS indicator. Pressing the ENTER button cycles through the statuses of each of the items below. • Remaining learning memory • Remaining macro steps • LCD timer setting • Backlight timer setting • Beep setting • Firmware version • Current clock time Either press the ENTER button or wait three seconds so that the LCD returns to the MAIN MENU. 1. [. . . ]