User manual MARANTZ RC-600PMD

[. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the RX-77 RF Extender. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a different circuit from the receiver. Consult the dealer or an experienced radio/TV technician for help. CAUTION: The user changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. For Europe Declaration of Conformity N° V04ECRC-600PMD: We, Marantz Europe B. V. , PO Box 8744, 5605 LS Eindhoven, The Netherlands declare under our responsibility that the Marantz product described in this user guide is in compliance with the corresponding technical standards such as EN301 489-1 of 2002-08, EN301 489-3 of 2002-08, EN300 220-1 of 2002-09 and IEC60950 of Edition 2001. [. . . ] Remember, the only way to NOT issue this command is to reveal the Device Overview page, press and hold the Left or Right Function buttons (now labeled "No IR") and select the device. 1 Tap and hold the MODE icon in the LOWER TOOL BAR more than 3 seconds. 2 Tap the "LEARN" button to switch to the LEARN mode. 3 Select the "Learn device action" button. 4 Complete steps 4 to 9 in "Programming Touch Screen buttons" on page 29. Instead of tapping a button on the Touch Screen, press the Device button you want to program. Programming the Hard Buttons per Device The Hard buttons are defined as the five hard buttons next right to the Touch Screen (Channel Up/Down, Volume Up/Down, Mute) and the ten buttons below the Touch Screen (Cursor Up, Down, Right, Left, Menu, Enter, Exit, HOME, Left and Right Function buttons). User Guide 30 DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:33 AM Page 35 Reference Notes · It is possible to teach commands to the LEFT (labeled "Back") and RIGHT (labeled "Ahead") Function buttons on the remote. But those commands can be re-programmed only via a PC using the editor software. · It is not possible to teach commands to the HOME button on the remote. Unless those commands were re-programmed via a PC using the editor software. · When the Cursor Navigation is active, the 4-way cursor buttons cannot be learned. Hard buttons can be programmed for a device specific command for a particular device on the remote (Programming locally). 1 Switch to the device for which you want to program the button. 2 Complete steps 1 to 9 in the programming Touch Screen buttons on page 29. 2 Tap the "LABEL" button to switch to the LABEL mode. 3 Tap the "Label device" button on the page. 4 Tap the device button which you want to label. 5 Complete steps 6 to 9 in "Labeling a Button" on page 33. Labeling a Page You can label all pages which are displayed in the Page Overview page. 1 Tap and hold the MODE icon in the LOWER TOOL BAR more than 3 seconds. 2 Tap the "LABEL" button to switch to the LABEL mode. 3 Tap the "Label page" button on the page. You can navigate to other device by tapping the DEVICE SCROLL buttons . 4 Tap the page button which you want to label. 5 Complete steps 6 to 9 in "Labeling a Button" on page 32-33. Note The font size cannot be set for devices and pages, in contrary to buttons. User Guide 34 DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:33 AM Page 39 Reference 3. Adding Devices If you have a device that is not provided in the Device Overview page, you can add it to the RC-600PMD. [. . . ] By using Wizz. it 9 with Windows PC, you can get the factory default configuration. Using Wizz. it 9, once the program is installed, open a configuration file named "RC-600PMD_default" in C:\Program Files\Marantz\Wizzit_9\Samples. Downloading this configuration will restore your RC-600PMD to its factory state except the setup items. By using the "Revert" function in the Setup, you can get the last downloaded configulation. 62 User Guide DFU RC-600PMD Ver1_2. qxd 5/28/2004 10:34 AM Page 67 Frequently Asked Questions How do I calibrate the Touch Screen? [. . . ]