User manual MARANTZ RC-9500

[. . . ] DFU RC9500 Ver1_2. qxd 5/28/2004 10:32 AM Page 1 Model RC9500 User Guide Touch Screen Remote Control DFU RC9500 Ver1_2. qxd 5/28/2004 10:32 AM Page 2 For US and Canada FCC Compliancy: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rule. These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is not guarantee that interference will not occur in a particular installation. [. . . ] 1 Switch to the device for which you want to program the button. 2 Complete steps 1 to 9 in the programming Touch Screen buttons on page 29. Instead of tapping a button on the Touch Screen, press the hard button you want to program. Note Only via PC, hard buttons can be programmed with a global function for all devices (Programming globally). When a command is learned to a hard button to a device page, it will only be issued when that device is active, even if a command has been programmed globally. Local learning overrides global programming. For example: One could program the CH+ & CH- buttons as the Chapter +/command when the DVD is active. Now, if you program the TV channel +/- globally (and any device other than the DVD is selected) the TV channel +/- commands will be issued. User Guide 31 DFU RC9500 Ver1_2. qxd 5/28/2004 10:33 AM Page 36 Reference 2. Labeling Buttons, Pages and Devices The following elements can be labeled: Buttons on a device page and Home page, Page (the name that appears on the Page Overview page), and Device (the name that appears on the Device Overview button and Device Overview page). Labeling a Button 1 Tap and hold the MODE icon in the LOWER TOOL BAR more than 3 seconds. 2 Tap the "LABEL" button to switch to the LABEL mode. 3 Tap the "Label button" button on the page. The last visited page in USE mode appears. 4 Navigate to the page that contains the button you want to label. The virtual "auto-zooming" mini-keyboard shows up. The button you want to label is displayed above the keyboard. Note The frames (texts with non-button function) cannot be labeled on the RC9500. User Guide 32 DFU RC9500 Ver1_2. qxd 5/28/2004 10:33 AM Page 37 Reference 6 Edit the label. To delete a character, press the Right Function button labeled "Del". To change the font size, Tap the "+" or "-" buttons beside the "Font" label on the page. Note If the font size does not fit in the button, the font size cannot increase. To enter a character, tap the keyboard near the character you want to use. The keyboard is zoomed in, allowing you to tap exactly the character you need. After you have tapped the character, the keyboard is zoomed out. Repeat this action for every character. Note You can zoom out again without tapping a character by tapping the "Unzoom" button. For capital characters and symbols, tap the "Shift" button repeatedly to display the keyboard you want. Note If you type a longer word than fits in the button, the font size will automatically get smaller. 7 Tap "Enter" button to save the changes. You will be redirected to the previous page. -orPress the Left Function button labeled "Back" to return to the page you were at without saving changes. 8 When you are finished labeling, you can return to the Mode Menu page by tapping label in the LOWER TOOL BAR. 9 Return to USE mode by pressing the Left Function button labeled "Exit". Note You cannot label buttons on the Device Overview page directly. You have to label them using "Label device" function in the LABEL mode. [. . . ] The RC9500 is calibrated when it leaves the factory, so normally you do not have to calibrate it yourself. It is possible that the RC9500 displays a message to calibrate the Touch Screen. If this message appears do the following. 1 Tap the INFO button in the Upper Tool Bar. [. . . ]