User manual MARANTZ SC-11S1

[. . . ] Model SC-11S1 User Guide Stereo Control Amplifier CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to aler t the user to t h e p r e s e n c e o f i m p o r t a n t o p e ra t i n g a n d maintenance (ser vicing) instructions in the literature accompanying the product. WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPON-DANTE DE LA PRISE ET POUSSER JUSQU'AU FOND. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. [. . . ] · Insert the plugs of the connections cords firmly into the connecting jacks. · Connect the wires correctly to the L (left) and R (right) channels. The red jack is the R (right) channel, and the white jack is the L (left) channel. · Make sure that input and output are connected correctly. · Refer also to the instruction manuals of components to connect equipment correctly. 2. European system (Pin w = HOT, Pin e = COLD) e This unit uses the 1. When a preamp or main amplifier adopting the European system is connected using a cable with XLR balanced connectors, the reproduced signal may be inverted of phase. In this case, refer to "ANALOG OUTPUT CONNECTOR PHASE SWITCHING", and set so that the correct phase is used. 11 ENGLISH ENGLISH CONNECTIONS 7 Connection Example1: Basic Connection for Normal Stereo Playback Connection Example with Input Source Components CD Player OPEN/ CLOSE PLA PLAY DISPLA OFF DISPLAY OFF DISPLA OFF DISPLAY OFF STOP 44. 1KHz 88. 2KHz 176. 4KHz Tuner, etc. DIMMER DVD Player, etc. DVD PLAYER DV-12S1 VIDEO ON/OFF RANDOM OPEN/CLOSE PLAY STOP PAUSE CD-R, etc. Tape deck, etc. POWER LOCK EXT. CLOCK EXT. CLOCK POWER ON/OFF ON/OFF INV. PHASE INV. PHASE SOUND MODE V-PART GRP TITLE DVD AUDIO 192kHz 96kHz TRK DIG OFF CHP PROGRESSIVE DOLBY D TEMAIN TOTAL VIDEO OFF L LAST MEMO CONDITION DOWN MIX CR LFE S RS PAUSE USE STANDBY FL OFF LS To LINE OUT jack To LINE OUT jack To LINE OUT jack To LINE OUT jack To LINE OUT jack To LINE IN jack To LINE IN jack Record player SC-11S1 PHONO INPUT L CD 1 - LINE - 2 1 - RECORDER - 2 L PRE OUT L MODEL NO. SC-11S R IN OUT PUSH R IN OUT R PHONO GND 2 PUSH PUSH PUSH R 3 1 2 3 1 L 3 2 1 R 3 2 1 L 3 2 1 R 3 2 1 L I 1 INPUT 2 BALANCED PRE OUT R ch CD player, etc. OPEN/ CLOSE PLA PLAY DISPLA OFF DISPLAY OFF DISPLA OFF DISPLAY OFF STOP 44. 1KHz 88. 2KHz 176. 4KHz L ch CD player, etc. OPEN/ CLOSE PLA PLAY DISPLA OFF DISPLAY OFF LOCK EXT. CLOCK EXT. CLOCK POWER ON/OFF ON/OFF INV. PHASE INV. PHASE SOUND MODE PAUSE USE L ch R ch DISPLA OFF DISPLAY OFF STOP 44. 1KHz 88. 2KHz 176. 4KHz LOCK EXT. CLOCK EXT. CLOCK POWER ON/OFF ON/OFF INV. PHASE INV. PHASE SOUND MODE PAUSE USE To BALANCED LINE OUT jack To BALANCED LINE OUT jack 12 CONNECTIONS Connection example to power amplifier · Set the PRE OUT button on the front panel to ON. To power outlet 1 - LINE - 2 1 - RECORDER - 2 L PRE OUT L AC IN MODEL NO. SC-11S1 R IN PUSH PUSH R OUT PUSH IN OUT R 3 2 1 L 3 2 1 R 3 2 1 L 3 2 1 R 3 2 1 L STEREO BI-AMP 1 INPUT 2 BALANCED PRE OUT AMP MODE Set to STEREO Unbalanced connection or balanced connection Set to STEREO Stereo Power Amplifier SM-11S1 AC IN UNBALANCED INPUT R L AMP MODE STEREO BTL R CH SPEAKER SYSTEMS MODEL NO. SM-11S1 BTL 1 L CH To power outlet BALANCED INPUT PUSH R PUSH L 3 2 1 2 3 1 2 3 1 BTL BTL R CH 2 L CH R ch Speaker L ch Speaker 13 ENGLISH ENGLISH CONNECTIONS 7 Connection Example 2: Stereo Complete Bi-amp Connection q The two amplifiers are connected by F. C. B. S. connection, connect with commercially available monaural monaural miniplugs or stereo stereo miniplugs as described in F. C. B. S. w Set the ID numbers as explained in HOW TO SET ID NUMBERS (page. When the ID1 amplifier is operated, the ID 2 amplifier will operate in sync. e Connect the analog output of the CD player etc. to the L ch input jacks of both pre-amps. As both pre-amps operate as monaural pre-amps in BI-AMP mode, do not use the R channel of the input jacks on these units. ¶ About Complete Bi-Amp Proposed by Marantz, the complete bi-amp connection is an advanced technique that enhances sound quality. The low and mid/high amplifiers are separated and independent of the preamplifier, therefore interference between low and mid/high sounds is reduced to a minimum. As a result, a wide sound environment can be reproduced. Note: Speaker systems connected using complete bi-amp connections must support bi-amp connections. Before connecting your speakers, check in the instruction manual that came with the speakers or contact the manufacturer to confirm whether they support bi-amp connection. SC-11S1 for L ch ¶ Set to ID 1 PHONO INPUT L CD 1 - LINE - 2 1 - RECORDER - 2 L PRE OUT L AC IN MODEL NO. SC-11S1 R IN OUT PUSH R IN OUT R To power outlet OUT STEREO BI-AMP PHONO GND 2 PUSH PUSH PUSH R 3 1 2 3 1 L 3 2 1 R 3 2 1 L 3 2 1 R 3 2 1 L IN Set to BI-AMP F. C. B. S. AMP MODE 1 INPUT 2 BALANCED PRE OUT Miniplug connecting cord × 2 (commercially available) F. C. B. S. [. . . ] 13. 5V (UNBALANCED) Total frequency distortion (20Hz ­ 20kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 002% (BALANCED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 003% (UNBALANCED) Frequency response (±3dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Hz ­ 120kHz (BALANCED) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Hz ­ 120kHz (UNBALANCED) Input sensitivity/Input impedance PHONO (MC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280µV / 100 PHONO (MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. 9mV / 47k BALANCED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mV / 20k CD/LINE/RECORDER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mV / 20k S/N rate (IHF A network, 0. 5V output) PHONO (MC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78dB (0. 5mV input) PHONO (MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89dB (5mV input) BALANCED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98dB (500mV input) CD/LINE/RECORDER . . . . . . . . . . . . . . . . . . . . . . 99dB (500mV input) Tone control BASS (50Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±8. 0dB TREBLE (20kHz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]