User manual MARANTZ SR7000

[. . . ] Read Instructions ­ All the safety and operating instructions should be read before the product is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. Heed Warnings ­ All warnings on the product and in the operating instructions should be adhered to. Follow Instructions ­ All operating and use instructions should be followed. [. . . ] When this setting is unavailable, "" is displayed. · If "VOLUME" is set to "FIXED", the multiroom output level cannot be adjusted from the A or B room. · MSPK cannot be on for both Room A and Room B at the same time. After you complete this portion of the setup, move the cursor to "RETURN" with the 3 or 4 cursor buttons and press the OK/ENTER button. This unit has 2 DC trigger control jacks, which can be used to link with input functions for the main room or multiroom. Each trigger can be setup separately. 1. 1. Select "5. PREFERENCE" from the MAIN MENU with the 3 or 4 cursor buttons and press the OK/ENTER button. Select "MULTI ROOM SETUP" with the 3 or 4 cursor buttons and select either "Room A" or "Room B" with the 1 or 2 cursor buttons. Press the OK/ENTER button to enter the setting. Select "5. PREFERENCE" from MAIN MENU with the 3 or 4 cursor buttons and press the OK/ENTER button. Select "DC TRIGGER SETUP 1or 2" with the 3, 4, 1 and 2 cursor buttons. Press the OK/ENTER button to enter the selection. DC TRIGGER SETUP DC TRIG-1:DISABLE TV TV : TAPE : DVD : CD/R : VCR1 : AUX2 : DSS : TUNER : AUX1 : 7. 1CH : 2. · The equalizer turns off when the Pure Direct mode, Source Direct mode, Dolby Headphone or Virtual mode is set. 6. ACOUSTIC EQ. MODE PRESET G. EQ1 CHECK AUTO : EQ. OFF ADJ RETURN NEXT EXIT 1. Select "6. ACOUSTIC EQ" from MAIN MENU with the 3 or 4 cursor buttons and press the OK/ENTER button. 6. ACOUSTIC EQ. MODE PRESET G. EQ CHECK AUTO : EQ. OFF PRESET ADJUST RESET:ALLCH 63-15. 0 CH :SR 125 -2. 5 250 -5. 0 +9 500 +9. 0 0d 1k +3. 5 2k -5. 5 4k -7. 0 8k-18. 5 63 250 1k 4k 16kHz 16k-20. 0 125 500 2k 8k RETURN EXIT CHECK MD:AUDYSSEY CH:SR +9 0d 63 250 1k 4k 16kHz 125 500 2k 8k AUTO 63-15. 0 125 -2. 5 250 -5. 0 500 +9. 0 1k +3. 5 2k -5. 5 4k -7. 0 8k-18. 5 16k-20. 0 EXIT RETURN ADJ RETURN NEXT EXIT 2. Select "EQ. MODE" with the 3 or 4 cursor buttons. 38 These modes allow you to set a 9-band graphic equalizer for each of the 7 channels. These menus are for confirming the results of AUTO SETUP function equalizer measurement (AUDYSSEY, FRONT, FLAT). 1. Select "6. ACOUSTIC EQ" from MAIN MENU with the 3 or 4 cursor buttons and press the OK/ENTER button. EQ ADJ" with the 3 or 4 cursor buttons. Press the OK/ENTER button to enter the selection. PRESET RESET:CH CH :FL +9 0dB 1. Select "6. ACOUSTIC EQ" from MAIN MENU with the 3 or 4 cursor buttons and press the OK/ENTER button. Select "CHECK AUTO" with the 3 or 4 cursor buttons. Press the OK/ENTER button to enter the selection. CHECK MD:AUDYSSEY CH:FL +9 0dB 2. [. . . ] 87. 5 ­ 108. 0 MHz Usable Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . IHF 1. 8 µV/16. 4 dBf Signal to Noise Ratio . . . . . . . . . . . . . . . . . . . Mono/Stereo 75/70 dB Distortion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mono/Stereo 0. 2/0. 3 % Stereo Separation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 kHz 45 dB Alternate Channel Selectivity . . . . . . . . . . . . . . . . . ± 300 kHz 60 dB Image Rejection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 MHz 70 dB Tuner Output Level . . . . . . . . . . . 1 kHz, ± 75 kHz Dev 800 mV Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 2 [INPUT] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 1 [OUTPUT] GENERAL Power Requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V 60 Hz Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 3A (SR7000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6. 5A (SR8001) Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33. 1 lbs (15. 0 Kg) (SR7000) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33. 1 lbs (15. 0 Kg) (SR8001) - disconnect the plug from the AC line supply after waiting at least three minutes, reconnect the plug to the AC line supply re-attempt to operate the equipment Remote Control Unit RC8001SR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]