User manual MARANTZ VP-4001

[. . . ] Model VP4001 User Guide DLP® Projector ENGLISH FRANÇAIS ESPAÑOL PORTUGUÊS Before using the projector, please read this user guide carefully. ENGLISH Introduction IMPORTANT · For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. · Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of "Supplied accessories" on page 10. Model No. : VP4001 Serial No. : WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly into the beam of light. WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. See bottom of projector. CAUTION RISK OF ELECTRIC SHOCK. [. . . ] · When you confirm the lower left position, the screen adjustments will be set and the "GEOMETRIC ADJUSTMENT" mode will end. Note · The placement of the screen and the projector may result in the image aspect ratio becoming slightly distorted. · Try "H&V KEYSTONE" when "GEOMETRIC ADJUSTMENT" does not fully correct trapezoidal distortion. 34 H & V KEYSTONE 1 2 Project the image and adjust the focus, image size, and projection angle. Press c KEYSTONE on the remote control repeatedly until "H & V KEYSTONE" is displayed. · When the "GEOMETRIC ADJUSTMENT" mode has been used to adjust the image, a confirmation screen displays before the "H & V KEYSTONE" screen, asking if you want to reset the adjustments or not. Then select RESET. R On-screen display H&V KEYSTONE END ENTER ADJUST RESET 3 Press P or R on the remote control to align the left and right sides of the projected image. Vertical Keystone Correction (Adjustment with P / R) 4 Press O or Q on the remote control to align the upper and lower sides of the projected image. Horizontal Keystone Correction (Adjustment with O / Q) Basic Operation 5 Press cKEYSTONE or iENTER on the remote control and the "H&V KEYSTONE" mode ends. Note · If adjustments are made using both "H KEYSTONE" and "V KEYSTONE" at the same time, the image aspect ratio may become slightly distorted. · When adjusting "H KEYSTONE" and "V KEYSTONE" at the same time, the values of adjustable angles for each setting become smaller. · The adjustable value of the "V KEYSTONE" becomes extremely small when "H KEYSTONE" is made to be the maximum value. 35 Image Projection (Continued) Aspect Mode This function allows you to modify or customize the Aspect mode to enhance the input image. Depending on the input signal, you can choose "FULL", "NORMAL", "ZOOM" or "THROUGH (Computer input only)" image. Press ASPECT on the projector or STANDBY/ON LAMP A ASPECT on the remote control. On the remote control RETURN ENTER On the projector TEMP. INPUT ENTER ASPECT AUTO SYNC ASPECT ASPECT button SYNC ASPECT MENU A PIC IRIS A VIDEO · "FULL" is fixed when 540P, 720P or 1080I signals are entered. Input Signal DVD / Video Image type FULL Output screen image NORMAL ZOOM 480I, 480P, 576I, 576P, NTSC, PAL, SECAM 540P, 720P, 1080I 16:9 aspect ratio : Cutout area on which images cannot be projected. 36 ASPECT INPUT ENTER MENU STANDBY/ON INPUT LAMP TEMP. RGB/COMP. IMAGE SHIFT PICTURE MODE R/C FREEZE INPUT IRIS ASPECT button 4:3 aspect ratio Letter box Squeezed 16:9 aspect ratio Computer Input Signal Computer Image type FULL Output screen image NORMAL ZOOM TROUGH Resolution lower than XGA 4:3 aspect ratio XGA (1024 × 768) 4:3 aspect ratio 1280 × 720 16:9 aspect ratio : Cutout area on which images cannot be projected. Note · You can select "ZOOM" when with a "VGA/SVGA" signal with a vertical frequency 60 Hz and less. However, when a "VGA/SVGA" signal with a vertical frequency of more than 60 Hz is used, "ZOOM" is not available. About Copyrights · When using the ASPECT function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size. · The use of the Aspect, Keystone Correction, Subtitle, or Overscan function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. · While watching non-widescreen images (4:3), if you use the ASPECT function to fill the screen or use the Overscan function to change the aspect ratio of a fixed-ratio input signal, parts of the outer edge of the image will be cut off or distorted. To watch original images as the producers intended, set ASPECT to "NORMAL" and Overscan to its default setting. 37 Basic Operation Operating with the Remote Control STANDBY ON Shifting the Projected Image Vertically (Image Shift) For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players or other connected devices. Press PIMAGE SHIFT. · The image moves up. COMP. 1 COMP. 2 S-VIDEO C1 VIDEO C2 RGB S HDMI V KEYSTONE RGB HDMI MENU IMAGE SHIFT buttons IMAGE SHIFT RETURN ENTER AUTO SYNC ASPECT PICTURE MODE PICTURE SYNC R/C FREEZE A PIC IRIS RGB/COMP. IMAGE SHIFT PICTURE MODE PIC IRIS MODE button IRIS button Press RIMAGE SHIFT. · The image moves down. IRIS IRIS Note · The Image Shift function operates when "Aspect" is not set to "THROUGH". · For details on Image Shift, see page 47. LIGHT FREEZE FREEZE button Switching the Iris Setting This function controls the quantity of the projected light and the contrast of the image. Press IRIS IRIS. · Each time the button is pressed while the display is on, the mode is switched in the following order: WIDE MEDIUM NARROW Selecting the Picture Mode You can select the appropriate picture mode to best match the projected image you are watching. Press PIC Note · For details on Iris, see page 45. PICTURE MODE. Freezing a Moving Image · When pressing PIC PICTURE MODE, the picture mode changes in the following order: Standard Natural Theater 2 Dynamic Theater 1 1 2 38 Press hFREEZE. · The projected image is frozen. Memory Note Press hFREEZE again to return to the moving image from the currently connected device. · See page 43 for details on the picture mode. Menu Items The following shows the items that can be set in the projector. The selectable items vary depending on the selected input, input signals, or adjustment values. Items that cannot be selected will be greyed out. Main menu Sub menu Picture Mode "Picture" menu PAGE 1 Picture Picture Mode Contrast Bright Color Tint Sharp Red Blue Standard 0 0 0 0 0 0 0 Comp. 1 Picture Page 43 Page 43 Standard Natural Dynamic Theater1 Theater2 Memory Contrast Bright Color Tint Sharp Red Blue -30 -30 -30 -30 -30 -30 -30 +30 +30 +30 *2 +30 *2 +30 *2 +30 +30 SEL. /ADJ. RETURN ENTER END Page 43 PAGE 2 Picture Picture Mode CLR Temp BrilliantColorTM C. Progressive DNR IRIS Lamp Setting Reset SEL. /ADJ. [. . . ] 41 RGB terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 RS-232C Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 RS-232C terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]