User manual MARANTZ VP11S1

[. . . ] Model VP-11S1 User Guide DLPTM Projector CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. Install in accordance with the manufacture's instructions. [. . . ] This allows such as a powered up/down screen, whenever the projector is turned on or off. Note: Do not use TRIG. 1 and TRIG. 2, as the power source. To connect with external devices, use an ordinal 3. 5mm mini-plug (mono) cable. , TRIG. 2(TRIGGER 2) Select ON or OFF at each aspect mode, such as Full, Normal, Zoom, V-Stretch and Through to control screen aspect ratio with powered up/down dual aspect ratio screen. Notes: Do not use TRIG. 1 and TRIG. 2, as the power source. To connect with external devices, use an ordinal 3. 5mm mini-plug (mono) cable. Connect the supplied AC power code. z Adjustment lever ( P. 12) Connect the analog RGB output from an IBM VGA or compatible equipment. Lift the projector and turn the adjustment lever right or left. The adjustable feet will extend from the projector. Then, release the lever, the adjustable feet is locked. c COMPONENT VIDEO IN 1 and 2 Terminals 1 and 2 have each Y, PB/CB, PR/CR terminals. Connect them to the component video output of a video device, AV amp/processor, DVD player, etc. x Screw holes for ceiling mount kit v S-VIDEO IN Connect the S-VIDEO output from a video equipment. m REMOTE IN/OUT By connecting this projector to another Marantz audio component using a supplied System Control cable, you can remotely operate the components as a single system. When connecting to component with a remote sensor (such as the SR9500, SR8500), be sure to connect the "REMOTE CONTROL IN" jack of this projector to the "REMOTE CONTROL OUT" jack of the component with the remote sensor. Note: For connections, always use the included bus control adaptor cable. . HDMI IN 1 and 2 Connect the digital signal (TMDS compliant, single link only) Note: To use the HDMI terminal, please follow the cautions on page 10. b VIDEO IN Connect the composite video output from a video equipment. /0 LIGHT ON/OFF Select ON : The terminal panel lights up. /1 RS-232C This is the control port for the custom installer. 5 Remote Controller ENGLISH a sdfg hjk l 0 1 2 3 4 5 6 7 8 9 TM0 TM1 TM2 TM3 TM4 TM5 TM6 TM7 TM8 a STANDBY button ( P. 18) STANDBY ON Turn the projector off. TM9 0 1 2 3 4 5 6 7 IRIS COMP. 1 LAMP COMP. 2 C. TEMP S-VIDEO GAMMA USER s IRIS button Switches lens aperture between F6. 0 and F3. 0. Select the Theater picture mode. Theater mode is designed for high fidelity black appearance and is good for movie pictures. Every time THTR button is pressed, the selection rotates in the order of Theater 1 Theater 2 Theater 3 Default. 5 THEATER (THTR) button ( P. 22) TM6 CINEMA button ( P. 24) TM7 FULL button ( P. 16) Sets aspect ratio to full mode. Turns the 2-3 pull down mode on and off. 6 STANDARD (STD) button ( P. 22) TM8 NORMAL button ( P. 16) Sets aspect ratio to normal mode. C1 HDMI 1 C2 HDMI 2 S VIDEO G1 d LAMP button Switches the lamp between the normal and energy-saving modes. H1 AUX 1 H2 AUX 2 V G2 A1 A2 RGB G3 THTR STD DYN G4 f C. TEMP button Sets color temperature to 1, 2, 3, 4, 5 or HB. Select the STANDARD picture mode. Standard mode is good for normal pictures. Every time the button is pressed, the selection rotates in the order of Standard 1 Standard 2 Standard 3 Default. TM9 ON button ( P. 16) Turn the projector on. 0 USER G1 button ( P. 22) 7 DYNAMIC (DYN) button ( P. 22) BLANKING B1 B2 B3 OFF g GAMMA button Sets the gamma curve to Theater, Standard, Dynamic, A, B, C, D or E, when the picture mode is set to User. V-MUTE MENU M ENTER INPUT A ASPECT CINEMA VCR MODE I INFO. BLACK LEVEL BLACK PATTERN 8 9 0 1 h COMP. 1 (Component video in 1) button ( P. 16) Select the Dynamic picture mode. Dynamic mode is good for visually dynamic pictures. Every time the button is pressed, the selection rotates in the order of Dynamic 1 Dynamic 2 Dynamic 3 Default. Selects the user mode. The user mode is for enjoying images at a userselected gamma curve. Every time the button is pressed, the selection rotates in the order of User 1 User 2 User 3. For more information on how to select gamma curve. [. . . ] ( Make the distance between the unit and the remote control closer. Select the "Wireless" position. (  P. 27) Notes: If the lamp still does not function after the replacement and initialization of the lamp life, contact a Marantz authorized dealer, or service center. In such case, shut power OFF and unplug the power cable from AC power outlet. [. . . ]