User manual MARKUS 800

[. . . ] English Users Manual Federal Communication Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : This device may not cause harmful interference This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communication Commission(FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] ESSID : referred to as SSID or Extended Service Set ID ASCII when WEP key or WPA key input : referred to as Characters HEX when WEP key or WPA key input : referred to as Hexadecimal Wireless security : referred to as Authentication method or Type. Encryption : referred to as Encryption Algorithm or Encryption Type NONE : referred to as NULL WPAPSK : referred to as WPA P-Key, WPA Pre-Shared Key or Network Key Key : referred to as Key Value - 36 - WIRELESS (AD-HOC Setup) There are several ways to set AD-HOC mode, but the following way is the easiest way to set AD-HOC setup. NETWORK setting of this device Go to NETWORK in SETUP menu and enter the following lists. B Static IP C 200. 200. 0. 2 (IP Address) D 255. 255. 255. 0(Subnet Mask) E 200. 200. 0. 1 WIRELESS setting of this device Go to WIRELESS in SETUP menu and enter the following lists. Ch11) D Select "WEP AUTO" E Select "NONE" Save setting and Return to main To save setting and return to main, press "SETUP" button on remote controller. - 37 - Set IP and Subnet mask with a PC On the PC, select Network connection in the control panel. Open Properties for the network connection that is connected to this device. Select Properties for the Internet protocol (TCP/IP). Select "Use the following address" Enter the IP address below. IP address : 200. 200. 0. 1 Subnet mask : 255. 255. 255. 0 Click "OK" Zero Configuration utility-a Open wireless zero configuration utility and choose a wireless network with same ESSID (ex. abc) that you entered with this device. Click "Connect". Zero Configuration utility-b After connecting successfully, you can browse shared folder with this device. Refresh network list. If you can not find the ESSID that you entered with this device, please try to click "Refresh network list" on wireless Network Connection. - 38 - LAN Sharing setting(PC) With shared folder, you can easily get multimedia file like movie, music and photo as if these files are in HDD of this device. To use shared folder, you must proceed the following steps. (based on window XP) NOTE. If firewalls are set in your PC, it may cause problem for this device to communicate with your PC. So, you need to disable the firewall program in your PC. Click right button of mouse on the folder that you want to share and select "Sharing and Security. . . ". 2. Check on " Share this folder on the network". Fill in the box of "Share name". And then, click "OK" and "Apply" button for confirmation. - 39 - 3. Then, each shared name will be listed up on screen if this device is connected. Network configuration under window 2000 STEP 1 Click the right button on "My Computer" icon and choose "manage" STEP 2 Go to " Local Users and Groups" - 40 - STEP 3 Click the " Users" folder STEP 4 Click the right button on "Guest" and click "Properties" STEP 5 Release the check box on "Account is disabled" and Apply this setting - 41 - STEP 6 Check that "Guest" will be activated. STEP 7 Click right button of mouse on the folder that you want to share and select "Sharing. . . " STEP 8 Click radio box on " Shared this folder" and click the "Permissions" - 42 - STEP 9 Click the "Add. . . " STEP 10 Click the "Add" after selecting "Guest" and Click "OK" STEP 11 Check the added "Guest" and apply this setting. - 43 - STEP 12 Go to security tab and click the "Add. . . " STEP 13 Click the "Add" after selecting "Guest" and Click "OK" STEP 14 Check the added "Guest" and apply this setting. - 44 - IP Address Setup :Ethernet Network using a direct connection Without a router or HUB, you can connect to a PC directly with crossed cable. If your PC has only one LAN card and it is already occupied for internet connection, you need one more LAN card for the connection if you use both simultaneously. Please see the below guides step by step to set IP address. 1. Select Network Connection in the Control Panel. Select the Local Area Connection to be connected with this device and click the right button of mouse. [. . . ] In case that you connect this device to TV indirectly through DVD player or VCR, etc, there may some noise on TV screen. Please connect this device to TV directly. In case there is some moisture inside this device when you move it from cold outside to warm inside, you need to wait for some time until it is conformed to inside temperature. 3. In case that the size of playing picture does not fit to TV screen. [. . . ]