User manual MARMITEK IP EYE ANYWHERE 20 ADVANCED INSTALLATION GUIDE

[. . . ] 0 1 PREFACE Thank you for purchasing the Marmitek Wireless* Pan-Tilt** MPEG4/MJPEG*** Network Camera, a powerful dual-codec*** wireless* network camera with the 1-way**** or 2-way***** audio function that provides the high-quality image and on-the-spot audio via the Internet connection. The Infrared LEDs and light sensor *****enable the camera to capture images even in the dark environment. The camera's pan/tilt** functions allow you to control the camera to monitor everywhere remotely. Through the GPIO** connectors, the camera can attach a variety of external devices for your specific purposes. [. . . ] NOTE If the camera is behind an NAT router of firewall, the suggested range to be used is from 1024 to 65535. 34 © MARMITEK Network >> IP Filter The IP Filter setting allows the administrator of the camera to limit the users within a certain range of IP addresses to access the camera. Start/End IP Address Assign a range of IP addresses that are not allowed to access the camera by entering the Start IP address and End IP address. When you are finished, click Add to save the range setting. You can repeat the action to assign multiple ranges for the camera. For example, when you enter 192. 168. 0. 50 in Start IP Address and 192. 168. 0. 80 in End IP Address, the user whose IP address located within 192. 168. 0. 50 ~ 192. 168. 0. 80 will not be allowed to access the camera. IP Eye Anywhere TM IP RoboCam TM 35 Deny IP List The list displays the range setting(s) of IP addresses that are not allowed to access the camera. To clear the setting, select a range of IP addresses from the list and click Delete. 36 © MARMITEK Network >> Wireless Setting* The camera supports WLAN while you use the wireless network. Select the Enable option to enable this feature. - Network ID (SSID}: Keep the default setting of this option to connect the camera to any access point under the infrastructure network mode. To connect the camera to a specified access point, set a SSID for the camera to correspond with the access point's ESS-ID. To connect the camera to an Ad-Hoc wireless workgroup, set the same wireless channel and SSID to match with the computer's configuration. IP Eye Anywhere TM IP RoboCam TM 37 Click Site Survey to display the available wireless networks, so that you can easily connect to one of the listed wireless networks. List of searching results - Wireless Mode: Select the type of wireless communication for the camera: Infrastructure or Ad-Hoc. - Channel: Select the appropriate channel from the list. - Authentication: Select the authentication method to secure the camera from being used by unauthorized user: Open, Shared-key, WPA-PSK, and WPA2-PSK. The following table explains the four options: Open Shared-key WPA-PSK/ WPA2-PSK The default setting of Authentication mode, which communicates the key across the network. Allow communication only with other devices with identical WEP settings. WPA-PSK/WPA2-PSK is specially designed for the users who do not have access to network authentication servers. The user has to manually enter the starting password in their access point or gateway, as well as in each PC on the wireless network. If you select Open or Shared-key as the Authentication mode, you need to complete the following settings: 38 © MARMITEK Encryption: Select the WEP option to enable the data encryption feature to secure the camera within the wireless network. Format: Once you enable the Encryption feature, you need to determine the encryption format by selecting ASCII or HEX. ASCII format causes each character you type to be interpreted as an eight-bit value. Hex format causes each pair of characters you type to be interpreted as an eight-bit value in hexadecimal (base 16) notation. Key Length: Select the WEP key length you use: 64 bits or 128 bits. WEP Key 1/2/3/4: Enter the WEP key(s) in the following boxes. If you select WPA-PSK or WPA2-PSK as the Authentication mode, you need to complete the following settings: Encryption: Select TKIP or AES. TKIP (Temporal Key Integrity Protocol) changes the temporal key every 10, 000 packets to insure much greater security than the standard WEP security. AES (Advanced Encryption Standard) is used to ensure the highest degree of security and authenticity for digital information. Pre-Shared Key: This is used to identify each other in the network. [. . . ] SNMP was designed to provide a common foundation for managing network devices. In LANs, a station consists of a device that can communicate data on the network. In FDDI, a station includes both physical nodes and addressable logical devices. Workstations, single-attach stations, dual-attach stations, and concentrators are FDDI stations. [. . . ]