User manual MARTIN AUDIO W0.5

[. . . ] 3. 1 W0. 5 and WM0. 5 The W0. 5 is a miniature high performance loudspeaker suited to a variety of applications from sports bars to live sound infill. It is a passive two-way system featuring an 8" (200mm) bass driver and a 1" (25mm) ferrofluid cooled HF driver on a 70 x 50 degree horn. The WM0. 5 is a wedge monitor version of the W0. 5, utilising the same drive units and horn. In its wedge configuration, the horn of the WM0. 5 exhibits a 50 x 70 degree dispersion pattern to increase the listening window in the vertical plane. [. . . ] Run cables so that they do not present a trip hazard which could pull the speaker over. When used outdoors in the wind, it may be necessary to add some weight to the base of the stand. When using a pole mount with a sub-bass system such as the WS2A, observe similar precautions. 4. 2 Stacking Ensure that the floor or stage is level and solid. Do not stack speakers too high outdoors where winds could topple the stack. Be aware that speakers producing very high power levels can move or creep. To avoid this, place friction material between the floor and speaker and between each speaker. 4. 3 Rigging and Suspension WARNING: Suspending the system should only be done by qualified personnel following safe rigging practices. Secure fixings to the building structure are vital. Seek help from architects, structural engineers or other specialists if in any doubt. All material © 2007. Subject to change without notice. 4 Martin Audio ­ WAVEFRONT PROFESSIONAL SERIES CONTENTS < > ENGLISH PRINT GUIDES The W0. 5, WM0. 5, W1, W2 and W3 are provided with threaded inserts to allow the suspension of a single enclosure. Never suspend one enclosure from another to form an array or cluster using these fittings. The W2 and W3 are provided with optional MAN flying points for array construction. The common practice of using commercially available eye bolts for suspension should only be undertaken with great caution. Eye bolts are strongest along the thread axis. Angling the enclosures will result in an angle pull and it is important to use eye bolts that are safe in these circumstances. Only forged shoulder eye bolts should be considered and it is important that the thread length is at least 30mm. A flat washer should be inserted between the eyebolt and the enclosure. [. . . ] Martin Audio is not liable for consequential damages. This warranty is exclusive and no other warranty is expressed or implied. This warranty does not affect your statutory rights. All material © 2007. Subject to change without notice. 9 Martin Audio ­ WAVEFRONT PROFESSIONAL SERIES CONTENTS < W2 TYPE > ENGLISH PRINT GUIDES FREQUENCY RESPONSE LOW FREQUENCY LIMIT DRIVERS RATED POWER RECOMMENDED AMPLIFIER SENSITIVITY MAXIMUM SPL IMPEDANCE DISPERSION CROSSOVER CONNECTORS FITTINGS DIMENSIONS WEIGHT SHIPPING DIMENSIONS SHIPPING WEIGHT Compact 2-way trapezoid, switchable active/passive 60Hz-18kHz ± 3dB -10dB @ 50Hz 12" (305mm) / 3" (75mm) voice coil 1" (25mm) exit HF compression driver LF/FR: 300W AES, 1200W peak HF: 60W AES, 240W peak 400-600W into 4 ohms LF/FR: 98dB, HF: 106dB 122dB continuous, 128dB peak F/R, LF & HF: 8 ohms nominal 70 degs horizontal, 40 degs vertical (-6dB) 1. 5kHz active or internal passive 2 x Neutrik Speakon NL4 8 x M8 1 x pole mounting socket 2 x MAN blanking plates 2 x rear kelp fittings (W) 365mm x (H) 554mm x (D) 364mm (W) 14. 4ins x (H) 21. 8ins x (D) 14. 3ins 24kg (53lbs) (W) 460mm x (H) 660mm x (D) 460mm (W) 18. 1ins x (H) 26ins x (D) 18. 1ins 24kg (52. 9lbs) All material © 2007. [. . . ]