User manual MARZOCCHI SHIVER 32

[. . . ] MARZOCCHI. COM SIGA LAS INSTRUCCIONES CORRECTAS EN EL MANUAL DE USUARIO O EN WWW. MARZOCCHI. COM TXC CORSA 22 33 44 44 29" 55 4X DIRT JUMPER 66 888 Table 1 - Intended use chart · · · · · · · · · 4X / DIRT JUMPER TREKKING / CROSS COUNTRY ALL MOUNTAIN / FREERIDE 3 ENGLISH or removing your bicycle to and from the bicycle carrier. Failure to fully loosen the quick release fastener, or any bending action while mounting or removing your bicycle to and from the carrier, could result in scratching, bending, or cause other damages your suspension system. Learn and follow the local bicycle laws and regulations, and obey all traffic signals, signs and laws while you ride. Always wear a properly fitted and fastened bicycle helmet that has been approved by ANSI, SNELL or CE, and any other safety equipment necessary for your riding style. [. . . ] In addition, if the oil volume is varied within the recommended ranges, it will be an additional setting element, thus allowing the modification of suspension system progressivity. Compared to the systems equipped with sealed cartridges, the Open Bath system allows reducing lubrication operations of the sliding parts. The Open Bath system assures an excellent lubrication even from the first "bottoming" of the fork, as well as in all use and weather conditions. In the systems equipped with sealed cartridge, special grease or oil is used for the lubrication of the internal sliding parts. The aforesaid lubricant does not work as additional setting element; therefore, the pre-established levels must be carefully observed. NOTE 6 WARNING! A The fastening screw thread of the disk brake caliper must be screwed by at least 10 mm on the brake support of the fork monolith. Make sure that the fastening screws are not damaged and that they are tightened with a torque spanner according to the specifications of the brake system manufacturer. tightening torque of 10 Nm. V-BRAKE SYSTEM SETTING - REMOVABLE SETTING 2A B Picture 2 - Dual crown forks installation on the frame: (2A) Crowns fastening, (2B) Steer tube maximum length between crowns H V-BRAKE SYSTEM SETTING - FIXED SETTING 2B BRAKE DISK SYSTEM SETTING - XC INTL STD Model Max length between crowns (H) 888 (except 888 RV) 160 mm (180 mm with high top crown (optional)) 888 RV 158 mm Table 1 - Steer tube maximum length between crowns 3. 2 Installing the brake system Installing the brake system is a delicate and critical operation that must be carried out by specialized personnel. Brake system installation requires specialized knowledge, tools and experience. General mechanical aptitude may not be sufficient to properly install your brake system. Please have your brake system installed only by an authorized Marzocchi Service Center. Improper installation of a disk brake system can overstress the caliper mountings, which may cause the caliper mountings to break, resulting in loss of control of the bicycle, an accident, personal injury, or death. The wheel should not make contact with, or come close to any portion of the fork. Then lift the front of the bicycle and spin the wheel a few times to verify the correct alignment with the disk brake. The wheel should not wobble from side to side or up and down. Check the owner's manual of the brake system for the proper specifications. · Tighten the screw positioned on each wheel axle clamp to the required torque (6±1 Nm) using a 4 mm Allen key (see 3C of Picture 3). For optimum fork performance, please follow the instructions below when installing the wheel: · Place the wheel in between each fork. · Align the center of the wheel with each wheel axle clamp (see 4A of Picture 4). · Insert the axle through the wheel axle clamp of the right fork, through the wheel, and then screw it into the wheel axle clamp of the left fork (see 4A of Picture 4). · Tighten the axle to the required torque (15±1 Nm) using a 6mm Allen key to the caps of the axle (see 4B of Picture 4). · Check for the proper fork-wheel alignment. To do this, begin by fully compressing the fork a few times. The wheel should not make contact with, or come close to any portion of the fork. [. . . ] This warranty does not cover items subject to normal wear due to the use of the suspension system, such as for example oil, oil seals, dust seals and bushes. We therefore ask you to check (or have your dealer check) its condition at the moment you purchase the suspension system, as that is the only time that it will be possible to replace such components. In addition, this warranty is void in the event that the suspension system is used with rental bicycles, unless Tenneco Marzocchi S. r. l. provided prior approval in writing for such use. [. . . ]