User manual MASTERCRAFT MARISTAR 230 SV 2002

[. . . ] Locate the battery insulator tab and gently pull to remove it. Slide the battery switch to the SOLAR position. SWITCH LEFT (START-UP / RESET) (STANDARD ALKALINES) Slide switch to LEFT position before (1) startup / reset or (2) any type of battery replacement SWITCH RIGHT (SOLAR OPERATION) (SOLAR-RECHARGEABLE BATTERIES) Slide switch to RIGHT position once solarrechargeable batteries are inserted and insulator tab is removed WARNING Do NOT recharge the included solarrechargeable batteries outside of this product because it will damage the batteries and other charging devices. BATTERY COMPARTMENT 4. Continue to section labeled "ACTIVATE SOLAR-POWERED OUTDOOR TRANSMITTER" ACTIVATE SOLAR-POWERED OUTDOOR TRANSMITTER Press the RESET key on the Sensor to activate the solar-powered transmitter and place it 5-10 feet from the Weather Station for 15 minutes. The outdoor temperature will show on the weather station within 60 seconds. [. . . ]  LCD will automatically turn OFF if the environment is too dark.  LCD will automatically turn ON if the environment is bright enough.  No information will be displayed when the LCD is OFF, but all the settings and operations will remain, except for the temperature and humidity measurements. If the solar mode setting is, OFF:  LCD will remain ON constantly. MIN/MAX TEMPERATURE READINGS: VIEW MIN/MAX: Press and release the PLUS button to view:  Outdoor Temperature minimum and maximum.  Indoor temperature minimum and maximum. RESET MIN/MAX: Press and hold the PLUS button for 10 seconds to reset the indoor and outdoor minimum and maximum temperatures to current temperatures. 4 DISPLAY MODES: Press and release the SET button to view different display modes:    Outdoor temperature in the first line on the left side and outdoor humidity in the second line on the left side. Shows indoor temperature in the first line on the right side and indoor humidity in the second line on the right. Outdoor temperature in the first line on the left side and outdoor humidity in the first line on the right side. Shows indoor temperature in the second line on the left side and indoor humidity in the second line on the right side. Indoor temperature in the first line on the left side and indoor humidity in the first line on the right side. Shows outdoor temperature in the second line on the left side and outdoor humidity in the second line on the right side Mounting Bracket RESET Button NOTE: Batteries are not replaceable in the sensor. SOLAR-POWERED OUTDOOR TRANSMITTER (915MHZ RECEPTION) The Weather Station receives outdoor data every 48 seconds. If, for instance, the Sensor is attached to a piece of metal, it may then either reduce or increase the transmitting range. For this reason, we recommend not to place the unit on any metal surfaces or in any position where a large metal or highly polished surface is in the immediate vicinity (garage doors, double-glazing, etc. ). Before securing the Sensor in place, please ensure that the Weather Station continuously receives the 915MHz signal from the Sensor from the desired location. TO REPLACE BATTERIES IN THE WEATHER STATION The Weather Station uses either the included 2 x solar-rechargeable batteries (charged by solar panel) or 2 x AA standard alkaline batteries (non-rechargeable; not included). The Weather Station comes with special solar-rechargeable batteries that should provide many years of service. If the batteries lose their ability to hold a charge, please dispose of them responsibly. Do NOT attempt to recharge the included solar-rechargeable batteries outside of the WS-6010U. Use standard alkaline batteries or contact customer support for more information. "Do NOT recharge the included solar rechargeable batteries in any device other than the product they came with. Recharging the alkaline rechargeable batteries in battery chargers or other third party devices will damage the batteries and charging device. " *Once the solar-rechargeable batteries are removed from the Weather Station, slide the battery switch to the left position before replacing the batteries. REGARDLESS OF THE TYPE OF BATTERIES TO BE INSTALLED, THE BATTERY SWITCH MUST BE IN THE LEFT POSITION WHEN THE BATTERIES ARE INSERTED. 6 If new solar rechargeable batteries are used, the battery switch should be moved to the right SOLAR position AFTER they are inserted in the unit. REPLACE INCLUDED SOLAR RECHARGEABLE BATTERIES WITH STANDARD ALKALINE BATTERIES 1. [. . . ] UNPOWERED FOR 15 MINUTES: It is important for the display to remain without power for at least 15 minutes. NOTE: Failure to allow a display to rest for 15 minutes can result in failure to connect with the outdoor sensor or missing segments on the display. SENSOR FIRST: GENTLY PUSH the RESET button on the TX62UTH-IT sensor. The code number and the security code ('20' for example) of the model will be displayed followed by the battery voltage will be shown on the LCD then the current temperature. [. . . ]