User manual MATSONIC MS6383E

[. . . ] This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] Install the Mainboard Install the mainboard into the system chassis. This mainboard uses the mini-ATX format with a twin-tier of I/O ports. Ensure that your case has an I/O template that can be used by this mainboard. Install the mainboard into the unit case. Follow the instructions provided by the case manufacturer using the screws and mounting points provided in the chassis. PWR1 1 J9 Connect the power cable from the ATX power supply unit to the power connector PWR1 on the mainboard. Connect the case switches and indicator LEDs to the bank of switch and LED connectors J9. See the illustration below for a guide to the pin functions of the J9 connector. Reset Switch Pins 17-18 Power Button/Suspend Switch Pins 21-22 21 22 Keylock Pins 8-10 HDD LED Pins 15-16 Power LED Pins 2-4-6 Speaker Pins 1-3-5-7 1 2 14 ! Install the Extension Brackets/Options This mainboard ships with a Fax/Modem DAA module and a 10BaseT/100BaseTX LAN extension bracket. As options, you can also obtain a digital audio extension bracket, an infrared port and an internal digital audio cable. The modules and extension brackets are used to transmit features on the mainboard to external connectors that can be fixed to the system chassis. Follow the steps below to install the extension brackets. Note: All the ribbon cables used on the extension brackets carry a red stripe on the pin-1 side of the cable. LAN Network Adapter Extension Bracket This bracket supports an RJ45 network connector and connects to the built in LAN header JP12 on the mainboard. 1 JP12 LAN Header LAN Extension Bracket 1. On the mainboard, locate the JP12 LAN header for this bracket. Plug the cable from the bracket into JP12. In the system chassis, remove a blanking plate from one of the expansion slots and install the extension bracket in the slot. Use the screw that held the blanking plate in place to secure the extension bracket. 15 ! Fax/Modem DAA Module The Fax/Modem card plugs directly into the mainboard adjacent to an expansion slot in the system chassis. When you remove the blanking plate from the system chassis, you can access the LINE and TEL RJ11 connectors on the metal edge of the Fax/Modem DAA module. JP10-MODEM Header GND 1 GND 3 GND 5 AUX 3V 7 HOOK 9 RIN 11 AUX 5V 13 MUTE 15 2 MCLK 4 FRA-SY 6 SCLK 8 RIN-WAK 10 GPIO 12 SDO 14 SDI 16 RST 1. Locate the JP10 modem header on the mainboard. Plug the Fax/Modem DAA module into the JP10 modem header. Remove the blanking plate adjacent to the Fax/Modem DAA module. Line & Tel RJ11 Sockets Modem DAA Module Modem Header 16 ! [. . . ] At the next dialog box, type in the new password, or just press Enter to disable password protection. Exit Highlight this item and press Enter to save the changes that you have made in the setup utility and exit the setup program. When the Save and Exit dialog box appears, press Y to save and exit, or press N to exit without saving. 34 Chapter 4 Software & Applications Introduction The support software CD-ROM that is included in the mainboard package contains all the drivers and utility programs needed to properly run our products. Please check all the README files for the latest information on installing and using the software. Using the PCI Sound Application 1. Before you install the PCI Sound drivers, make sure your Operating System has been installed, otherwise the PCI Sound might be detected as "Other device" by the device manager of your OS. [. . . ]