User manual MATSONIC MS7047D

[. . . ] Main Board User's Manual able Table of Contents Chapter 1-1 1-2 1-3 Chapter 2-1 2-2 2-3 2-4 2-5 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is important to pay attention to the correct cables and pin orientation (i. e. , not to reverse the order of these two connectors. ) Over-ride Power Button Operation Pin 1 Power Indicator LED Definition +5V DC No Connection Ground 2 3 Software Power-Off Control This mainboard can be powered down using the Windows 95/98 Software Power-Off function. To power down your computer, click the START button on the Windows 95/98 task bar. Select "Shut Down The Computer" and the system turns off. The message "It is now safe to turn off your computer" will not be shown when using this function. 13 Chapter 2 C. Green Switch/Green LED Connector Some ATX cases provide a Green switch which is used to put the system in Suspend mode. In Suspend mode, the power supply to the system is reduced to a trickle, the CPU clock is stopped, and the CPU core is in it's minimum power state. The system is woken up whenever the keyboard or mouse is touched. The system resumes in different ways as defined by Power Management Setup screen in BIOS. System Reset Switch Connector This connector should be connected to the reset switch on the front panel of the system case. The reset switch allows you to restart the system without turning the power off. Pin 1 2 Definition System GND E. Speaker Connector Pin 1 2 3 4 Definition Speaker Signal No Connection No Connection +5V DC F. IDE Activity LED Connector The IDE activity LED lights up whenever the system reads/writes to the IDE devices. Turbo LED Connector This mainboard does not have a Turbo/De-turbo speed modes. So the turbo LED will always light. Blinking LED in Suspend Mode While in Suspend mode, the LED light on the front panel of your computer will flash. Suspend mode is entered by pressing the Override Power Button, pushing the Green button on your ATX case, or enabling the Power Management and Suspend Mode options in BIOS's Power Management menu. 14 Hardware Setup PS/2 Keyboard Power On Function (JP1) 1 Disabled 1 Enabled This board is able to be turned on by the keyboard. To use this function, enable the Power On Function option in BIOS's Integrated Peripherals screen (See section 3-8). You must also set this jumper's cap to pins 2-3 to use this function. Some outof-date keyboards may require larger current than supplied by the Suspend 5V of modern power supplies. When using older keyboards disable this function. Audio Line_out or Speaker_out (JP2/JP3) JP2 1 JP2 1 JP3 JP3 Speaker_ out Line_out (default) This jumper allows you to select between audio line-out or speaker out function. Set both JP2 and JP3 pins to 1-2 for line-out function or set both JP2 and JP3 pins to 2-3 for speaker out function. . Smart Bus Connector (JP4) This connector supports Aux-input for connecting DVD or other audio devices. 15 Chapter 2 Chassis Intrusion Detection (JP5) This board supports the chassis instruction monitoring feature of the management extension hardware by means of a mechanical or photo sensor switch attached to the motherboard through this 1x3-pin chassis security header. The mechanical switch is set to open for normal computer operation. IR/CIR Connector (JP6) If you enable the IR/CIR Address Select in BIOS's Integrated Peripherals menu the IR/CIR port will let you select the IRQ and IR/CIR Mode to support IR/CIR functions. Onboard Audio (JP7) 1 1 Enable Disable This function allows you to enable and disable the on board audio. You must set the jumper's cap to pins 1-2 to enable or set pins 2-3 to disable this function. AC'97 CODEC selector (JP8) 1 1 Onboard CODEC (Default) CNR (Soft-Audio/Modem riser) Short pin 1-2 to enable onboard AC`97 CODEC. [. . . ] See the Readme. txt file in the CD-ROM's root directory for installation instructions of the Acrobat Reader. The Mainboard software guide discusses the following items: The following items are discussed in the TXT or PDF files: Bus Master/PIO IDE Driver Installation USB Driver Installation Updating Your System BIOS Installing and Using a Desktop Management Interface (DMI) Utility for DOS Sound Drivers and Utility Installation AGP VGA Drivers for Win95/98/2000/NT Optional Creative 5880 audio driver for Win98, NT and Win2000 The DMI utility is a DOS utility, operating under Windows or other operating system might cause damage to the BIOS. 25 Chapter 4 Memo 26 Appendix I On Board I/O Addresses & IRQ Maps System Resource 1. Programmable INT IRQ IRQ0 IRQ1 IRQ2 I/O Address 040, 043 060, 064 0020, 0021, 00A0, 00A1 2F8, 2FF 3F8, 3FF 3F0, 3F7 378, 37F 070, 071 060, 064 0F0, 0FF 1F0, 1F7 170, 177 4. PS/2 Mouse 10. Math coprocessor 11. IDE 1 12. IDE 2 IRQ3 IRQ4 IRQ6 IRQ7 IRQ8 IRQ12 IRQ13 IRQ14 IRQ15 @IRQ 5, 9, 10 and 11 are available for interface cards. 27 User's Manual Memo 28 Appendix II Embedded Flash Utility This mainboard is equipped with an Erasable Flash ROM and an Embedded Flash Utility which allows the user to update the BIOS to a newer version. [. . . ]