User manual MATSONIC MS7057 C

[. . . ] Caution! When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the motherboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the mainboard, you may cause serious damage to both the mainboard and the processor. On most mainboards, there are small surface-mount resistors near the processor socket, which may be damaged if the cooling fan is carelessly installed. Avoid using cooling fans with sharp edges on the fan casing and the clips. [. . . ] Note: The CNR slot is shared with PCI 6. You can install an expansion card into either the CNR slot or PCI 6, but you cannot use both slots at the same time. C PU FA N 1 JP 12 JP 11 JP 10 JP 9 JP 8 JP 3 1 1 1 1 1 1 1 JP 6 1 JP 4 LE D 1 J1 SIR 1 ATX 1 C D1 C D2 1 A G P slot P CI1 P CI2 D IM M 2 D IM M 1 D IM M 3 ID E2 PC I slots P CI3 3V + B T1 P CI4 JP 1 1 JP 2 PA N EL 1 1 ID E1 C AS FA N1 1 A G P1 FD D 1 U SB 1 W O L1 W O M 1 P CI5 P CI6 C N R slot C NR 1 28 1. Before installing an expansion card, check the documentation for the card. If the card is not Plug and Play, you may have to manually configure the card before installation. In the system case, remove the blanking plate from the slot in the system case that corresponds to the expansion slot that you are going to use. Position the edge connector of the add-in card over the expansion slot. Position the metal bracket of the card in the empty slot in the system case. Install the edge connector of the add-in card into the expansion slot. Press down quite firmly so that you are sure that the edge connector is correctly seated in the slot. Secure the metal bracket of the card in the empty slot, in the system case, with a screw. For some add-in cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the add-in card. PC I add-in card M etal bracket Edge C onnector PC I slot 29 Other Options This section lists the other options that come with this mainboard. C PUFAN 1 JP12 JP11 JP10 JP9 JP8 JP3 1 1 1 1 1 1 1 JP6 1 JP4 LED 1 J1 SIR 1 ATX1 C D1 C D2 1 DIM M1 DIM M2 1 SIR 1 PC I1 DIM M3 IDE2 PC I2 PC I3 3V + B T1 PC I4 JP1 1 JP2 PAN EL1 1 IDE1 CA SFA N1 1 A GP1 FDD 1 U SB1 W OL1 W OM 1 PC I5 PC I6 C NR 1 1 U SB 1 W O L1 W O M 1 30 SIR1: Serial Infrared Connector. Connect the cable from the optional IR port to SIR1 (for SIR infrared). After you have connected the cable, secure the optional IR port to the appropriate location on your system case. This option can be purchased from third-party vendors. Note: An IR port may use some of the resources required by a second serial port or a fax/modem card. If you have more than one of these items installed, you may not be able to use them at the same time. You can use the Peripherals page of the Setup Utility to switch resources between an IR port and a second serial port. See Chapter 3 for more information. USB1: Extra USB Port Header Some cases come with USB ports on the front panel. If your case has these ports, you can connect them to the USB1 header. WOL1: Wake on LAN If you have installed a LAN/modem card, you can use the cable provided with the card to plug into the WOL1 connector on the mainboard. When your system is in a power­saving mode, any incoming calls to the LAN automatically resume the system. You must enable this item using the Power Management page of the Setup Utility. See Chapter 3 for more information. WOM1: Wake on Modem If you have installed a fax/modem card, you can use the cable provided with the card to plug into the WOM1 connector on the mainboard. When your system is in a power­saving mode, any incoming calls to the modem automatically resume the system. [. . . ] 66 PC-cillin Software The PC-cillin software program provides anti-virus protection for your system. WinNT ­ \UTILITY\PC-CILLIN\WINNT\SETUP. EXE !Win9x ­ \UTILITY\PC-CILLIN\WIN98\SETUP. EXE Anti-virus software is provided for WINNT/2000 and WIN95/98. GAMUT The Gamut audio rack software for the built-in sound system is provided for different languages. Go to the directory \UTILITY\GAMUT and choose either the English or Chinese subdirectory; then run SETUP. EXE to install the application software. MediaRing Talk To install the MediaRing Talk voice modem software for the built-in modem, go to the directory \UTILITY\MEDIARING TALK; then run MRTALK-SETUP7. 2. EXE to install the application software. Super Voice To install the Super Voice voice, fax, data communication application for use with the built-in fax/modem, go the directory \UTILITY\SUPERVOICE; then run PICSHELL. EXE to install the application software. 67 Realtek-codec Folder Installation Notes This folder has software and drivers for the Realtek codec sound system that is integrated on this mainboard. [. . . ]