User manual MATSONIC MS7122A

[. . . ] MS7122A ISA/PCI AGP Mainboard with Onboard PCI IDE and Super Multi-I/O TRADEMARK All products and company names are trademarks or registered trademarks of their respective holders. These specifications are subject to change without notice. Manual Revision 5. 0 October 11, 1999 MS7122A Table of Contents Section 1 Introduction Components Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Overview MS7122A Form-factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 I/O Shield Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] : Enabled : Enabled : Enabled : Disabled : Disabled : Enabled : Disabled : : : : : Auto Auto Auto Auto Auto Esc F1 F5 F7 : : : : Quit Help Old Values Load Setup Defaults é ê è ç : Select Item PU/PD/+/- : Modify (Shift) F2 : Color Figure 6: PCI Configuration Setup PNP OS Installed: Do you have a PNP OS installed on your system. Yes: Select if you are using a PNP OS No: Select if your OS does not support PNP. Resources Controlled By: Who controlled the system PNP/PCI resources. Manual: PNP Card's resources will be controlled manually. You can set which IRQ-X and DMA-X are assigned to PCI/ISA PNP or Legacy ISA Cards. Auto: If your ISA card and PCI card are all PNP cards, BIOS will assign the interrupt resource automatically. Page 4-15 BIOS Reset Configuration Data: MS7122A This setting allows you to clear ESCD data. . Enabled: If you have plugged in some Legacy cards to the system and they were recorded into ESCD (Extended System Configuration Data), you can set this field to Enabled in order to clear ESCD. CPU to PCI Write Buffer: When enabled, up to four D words of data can be written to the PCI bus without interruting the CPU. When disabled, a write buffer is not used and the CPU read cycle will not be completed until the PCI bus signals that it is ready to receive the data. PCI Dynamic Bursting: When Enabled, data transfers on the PCI bus, where possible, make use of the high-performance PCI bust protocol, in which graeater amounts of data are transferred at a single command. PCI Master 0 WS Write: When Enabled, writes to the PCI bus are command with zero wait states. PCI Delay Transaction: The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2. 1. PCI #2 Access #1 Retry: This item allows you enabled/disable the PCI #2 Access #1 Retry. The Choice: Enabled, Disabled. Page 4-16 MS7122A 4-6 Load Setup Defaults BIOS The "LOAD SETUP DEFAULTS" function loads the system default data directly from ROM and initializes the associated hardware properly. This function will be necessary only when the system CMOS data is corrupted. 4-7 Integrated Peripherals ROM PCI/ISA BIOS(2A6LGPAA) INTEGRATEDPERIPHERALS AWARD SOFTWARE, INC. OnChip IDE Channel0 OnChip IDE Channel1 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary MasterUDMA Secondary Slave UDMA Init Display First Onboard FDD Controller Onboard Serial Port 1 Onboard Serial Port 2 UART 2 Mode IR Function Duplex TX, RX inverting enable : Enabled : Enabled : Enabled : Auto : Auto : Auto : Auto : Auto : Auto : Auto : Auto : PCI Slot : Enabled : Auto : Auto : HPSIR : Half : No, Yes Onboard Parallel Port Onboard Parallel Mode ECP Mode Use DMA Parallel Port EPP Type Onboard Legacy Audio Sound Blaster SB I/O Base Address SB IRQ Select SB DMA Select MPU-401 MPU-401 I/O Address FM Port (388-38BH) Game Port (200-207H) Esc F1 F5 F7 : : : : Quit Help Old Values Load Setup Defaults : 378/IRQ7 : ECP/EPP :3 : EPP1. 9 : Enabled : Disabled : 220H : IRQ 5 : DMA 1 : Disabled : 330-333H : Disabled : Enabled éêèç : Select Item PU/PD/+/- : Modify (Shift) F2 : Color Figure 8: Integrated Peripherals Note: If you do not use the Onboard IDE connector, then you will need to set Onboard Primary PCI IDE: Disabled and Onboard Secondary PCI IDE: Disabled Note: The Onboard PCI IDE cable should be equal to or less than 18 inches (45 cm. ). IDE Prefetch Mode: Enable prefetching for IDE drive interfaces that support its faster drive accesses. If uou are getting disk drive errors, change the setting to omit the drive interface where the errors occur. Depending on the configuration of your IDE subsystem, this field may not appear, and it does not appear when the Internal PCI/IDE field, above, is Disabled. The Choice: Enabled, Disabled. Page 4-17 BIOS Onchip IDE Channel: The default value is Enabled. Enabled: Enables Onboard IDE primary port. Disabled: Disables Onboard IDE primary port. [. . . ] Select Yes to start. Disk To Image (Disk Backup) 1. Select the location of the Source drive. 2. Select the location for storing the backup file. A-13 Appendix MS7122A 3. Click OK to display the following confirmation screen. [. . . ]