User manual MATSONIC MS9147C VERSION 5.0A

[. . . ] Mainboard User's Manual This publication, photographs, illustrations and software are under the protection of international copyright laws and all rights reserved. It does not allow any reproduction of this manual, content and any materials contained herein without the written consent of the authentic manufacturer. The information in this manual is subject to change without notice. The manufacturer does neither represent nor warrant the contents hereof; and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] Features Setup CPU PnP Setup Hardware Monitor Change Password Exit You can use cursor arrow keys to highlight anyone of options on the main menu page. Press Enter to select the highlighted option. Press the Escape key to leave the setup utility. Hold down the Shift key and press F2 to cycle through the Setup Utility's optional color schemes. Some options on the main menu page lead to tables of items with installed values that you can use cursor arrow keys to highlight one item, and press PgUp and PgDn keys to cycle through alternative values of that item. The other options on the main menu page lead to dialog boxes that require your answer Yes or No by hitting the Y or N keys. If you have already changed the setup utility, press F10 to save those changes and exit the utility. Press F5 to reset the changes to the original values. Press F6 to install the setup utility with a set of default values. Press F7 to install the setup utility with a set of high-performance values. 24 3: BIOS Setup Utility Standard CMOS Setup Page This page displays a table of items defining basic information about your system. AMIBIOS SETUP ­ STANDARD CMOS SETUP (C) 2000 American Megatrends, Inc. All Rights Reserved Date (mm/dd/yy) : Mon Sept 05, 2002 Time (hh/mm/ss) : 17:08:22 Type Pri Master : Auto Pri Slave : Auto Sec Master : Auto Sec Slave : Auto LBA Blk PIO 32Bit Size Cyln Head WPcom Sec Mode Mode Mode Mode On On On On Floppy Drive A : 1. 44 MB 3 1/2 Floppy Drive B : Not Installed Month : Jan ­ Dec Day : 01 ­ 31 Year : 1901 ­ 2099 ESC : Exit : Select Item PU/PD/+/- : Modify (Shift)F2 : Color F3 : Detect All HDD Date & Time IDE Pri Master Pri Slave Sec Master Sec Slave Floppy Drive A Floppy Drive B Use these items to set up system date and time Use these items to configure devices connected to the Primary and Secondary IDE channels. To configure an IDE hard disk drive, choose Auto. If the Auto setting fails to find a hard disk drive, set it to User, and then fill in the hard disk characteristics (Size, Cyls, etc. ) manually. If you have a CD-ROM drive, select the setting CDROM. If you have an ATAPI device with removable media (e. g. a ZIP drive or an LS-120), select Floptical. Use these items to set up size and capacity of the floppy diskette drive(s) installed in the system. 25 Mainboard User's Manual Advanced Setup Page This page sets up more advanced information about your system. Any changes can affect the operation of your computer. AMIBIOS SETUP ­ ADVANCED SETUP (C) 2000 American Megatrends, Inc. All Rights Reserved Quick Boot 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Devices S. M. A. R. T. for Hard Disks BootUp Num-Lock Floppy Drive Swap Floppy Drive Seek Password Check Boot To OS/2 L2 Cache System BIOS Cacheable SDRAM Timing by SPD SDRAM Frequency SDRAM CAS# Latency SDRAM Bank Interleave AGP Mode AGP Comp. Driving Enabled IDE-0 Floppy CDROM Yes Disabled On Disabled Disabled Setup No Enabled Enabled Disables 100MHz 2. 5 Disabled 4X Auto CB AGP Aperture Size Auto detect DIMM/PCI Clk CLK Gen Spread Spectrum 64MB Disabled Disabled ESC : Quit F1 F5 F6 F7 : Help : Select Item PU/PD/+/- : Modify : Old Values (Shift)F2 : Color : Load BIOS Defaults : Load Setup Defaults Quick Boot 1st Boot Device 2nd Boot Device 3rd Boot Device Try Other Boot Device If you enable this item, the system starts up more quickly be elimination some of the power on test routines. Use these items to determine the device order the computer uses to look for an operating system to load at start-up time. [. . . ] Below you can find a brief description of each software program, and the location for your mainboard version. More information on some programs is available in a README file, located in the same directory as the software. Note: Never try to install software from a folder that is not specified for use with your mainboard. Before installing any software, always inspect the folder for files named README. TXT, INSTALL. TXT, or something similar. [. . . ]