User manual MATSONIC MS9327E

[. . . ] Mainboard User's Manual This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. [. . . ] Connect the cable to the appropriate connector. CD_IN1 Pin 1 2 3 4 Signal CD IN L GND GND CD IN R CD_IN2 Pin 1 2 3 4 Signal GND CD IN R GND CD IN L If you have installed a secondary CD-ROM drive or DVD-ROM drive, you can connect the drive audio cable to the onboard sound system. On the mainboard, locate the 4-pin Aux-In header AUX1, connect the cable to the connector. Pin 1 3 Signal AUX_L AUD_GND Pin 2 4 Signal AUD_GND AUX_R 21 Mainboard User's Manual Infrared Port You can connect an infrared port to the mainboard. You can purchase this option from third-party vendors. Locate the infrared port IR1 header on the mainboard. If you are adding an infrared port, connect the ribbon cable from the port to the IR header and then secure the port to an appropriate place in your system chassis. Pin 1 2 3 4 5 Signal VCC 5V NC IRRX GROUND IRTX Expansion Slots This mainboard has four 32-bit PCI slots and one ACR slot. Follow the steps below to install a PCI/ACR expansion card. Locate the ACR or PCI slots on the mainboard. Remove this slot cover from the system chassis. Insert the expansion card edge connector into the slot and press it firmly down into until fully seated. Secure the expansion card bracket to the system chassis with a screw. 22 3: BIOS Setup Utility Chapter 3 BIOS Setup Utility Introduction The BIOS Setup Utility records settings and information about your computer such as the date and time, the type of installed hardware, and various configuration settings. Your computer applies that information to initialize all the components while booting up, and the basic functions of coordination between system components. If the Setup Utility configuration is incorrect, it may cause the system to malfunction. It can even stop your computer booting properly. If it happens, you can use the clear CMOS jumper to clear the CMOS memory that has stored the configuration information; or you can hold down the Page Up key while rebooting your computer. Holding down the Page Up key also clears the setup information. You can run the setup utility and manually change the configuration. You might need to do this to configure some hardware installed in or connected to the mainboard, such as the CPU, system memory, disk drives, etc. 23 Mainboard User's Manual Running the Setup Utility Every time you start your computer, a message appears on the screen before the operating system loading that prompts you to "Hit <DEL> if you want to run SETUP". Whenever you see this message, press the Delete key and the Main menu page of the Setup Utility appears on your monitor. AMIBIOS SIMPLE SETUP UTILITY ­ VERSION 1. 21. 10 (C) 2000 American Megatrends, Inc. All Rights Reserved Standard CMOS Setup Advanced Setup Power Management Setup PCI / Plug and Play Setup Load Optimal Settings Load Best Performance Settings Esc : Quit : Select Item (Shift)F2 : Change Color F5 : Old Values F6 : Optimal values F7 : Best performance values F10 : Save&Exit Standards COMOS setup for changing time, date, hard disk type, etc. Features Setup CPU PnP Setup Hardware Monitor Change Password Exit You can use cursor arrow keys to highlight anyone of options on the main menu page. Press Enter to select the highlighted option. Press the Escape key to leave the setup utility. [. . . ] A second dialog box asks you to retype the password for confirmation. Press Enter after you have retyped it correctly. The password is then required to access the Setup Utility or for that and at start-up, depending on the setting of the Password Check item in Advanced Setup. Change or Remove the Password Highlight this item, press Enter and type in the current password. [. . . ]