User manual MAXDATA MPL 1510 2210 MAINBOARD

[. . . ] MAXDATA PLATINUM Server Board User Manual MAXDATA PLATINUM Server Board 1 2 Contents Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Server Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Back Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Processor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can make the connection over a LAN or by using a modem or direct serial cable to the Emergency Management Port (EMP). You can set up the server to notify you when various events occur. Alerts can be delivered either as telephone pages or over the LAN. Instructions for setting up the server for remote LAN and serial/modem access and for setting up the server to proactively alert or page you are given below. How to Set Up Remote LAN Access To set up the server so you can access it from a remote workstation, you can use either the Server Configuration Wizard or the System Setup Utility. To use the Server Configuration Wizard to configure remote LAN access: 1. Use the Resource CD to boot the server to the Server Configuration Wizard. Select Server Configuration Wizard and Continue. Select the box that says configure this server for remote Server Management over a LAN connection . Review the system date and time for accuracy and Continue. In the IP Setup screen, choose either: · DHCP: the IP address for the server is automatically assigned by the DHCP (dynamic host control protocol) server on the network. The Host, Gateway, and Subnet Mask boxes in the dialog are ignored. · Static: assign the IP address for the server using the Host, Gateway, and Subnet Mask boxes in the dialog. · · · · If you chose Static IP Setup in the previous step, fill in the IP addressing boxes: Host IP Address: the IP address of this server. Gateway IP Address: the IP address of the router for this server. Subnet Mask: the IP address for the server subnet. The server uses this to decide if the alert destination is on the same subnet. The IP address of the alternate router for this server. 8. Click the LAN Password button (optional) to require that a password be entered before a user can perform server management functions on this server from a workstation on the LAN. Select the LAN Access Mode to set the points at which LAN connectivity can be activated: · Always Available: a remote system can initiate a LAN connection, regardless of the server`s state or health. · Restricted: power control functions, such as power down, front panel NMI, and system reset cannot be performed remotely. · Disabled: remote LAN connections cannot be initiated. 36 Configuration Software and Utilities 10. Select the SOL Access Mode to set the user access level that is required for connecting to the server using Serial over LAN. [. . . ] BIOS recovery succeeded, ready for power-down, reboot. Recovery complete EFh Bootblock Error Beep Codes Table 16. Bootblock Error Beep Codes Beeps 1 2 3 4 5 6 7 8 9 10 11 Error message Refresh timer failure Parity error Base memory failure System timer Processor failure Keyboard controller Gate A20 failure Processor exception interrupt error Display memory read/write error ROM checksum error Shutdown register error Invalid BIOS Description The memory refresh circuitry on the motherboard is faulty. **See , , 3-Beep-Boot Block Failure Error Code" table for additional error details. The BIOS cannot switch to protected mode. [. . . ]