User manual MAXDATA MPL 500 1200 3200 CASE

[. . . ] MAXDATA PLATINUM Server Case Users' Manual MAXDATA PLATINUM Server Case Manual 1 2 Part 1 Server Case MAXDATA PLATINUM Server Case Manual 3 4 Contents 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additions for the SC5100 Pedestal Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additions for the SC5100 Rack Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you haven't already done so, remove the top piece of foam epac from the system fans. Remove and save the two screws that secure the drive carrier to the chassis. Slide the drive carrier out of the chassis. You may need to push the carrier from the inside of the chassis. Figure 16. Remove the drive from its protective wrapper and place it on an antistatic surface. Record the drive model and serial numbers in your equipment log. Set any jumpers or switches on the drive according to the drive manufacturer's instructions. Place the drive into the carrier component side down and with the power and data connectors facing the rear of the carrier. The connectors should be flush with the rear of the carrier. 8. Holding the drive in place, turn the carrier upside down. MAXDATA PLATINUM Server Case Manual 29 A B C Figure 17. Attaching a Hard Drive to a Carrier A. Line up the screws holes in the carrier with the screw holes in the drive. Using four screws of the appropriate size and length, attach the drive to the carrier. 30 Setting Up the Chassis B A Figure 18. Insert and tighten the screws removed in Step 1. Attach data and power cables to the drive. MAXDATA PLATINUM Server Case Manual 31 Hot Swap SCSI Hard Disk Drives The chassis may contain the optional hot swap drive bay and 5 drive carriers, but no hard disk drives. Refer to the Intel customer support website for a list of approved SCSI devices. CAUTION Electrostatic discharge (ESD) and ESD protection: ESD can damage disk drives, add-in boards, and other components. This server can withstand normal levels of environmental ESD while you are hot-swapping SCSI hard disk drives. However, we recommend doing all procedures in this manual only at an ESD-protected workstation. If one is not available, you can provide some ESD protection by wearing an antistatic wrist strap attached to chassis ground of the server ­ any unpainted metal surface ­ when handling components. Installing a Hot Swap Hard Disk Drive 1. Press the latch on the top of the carrier handle down, pull the carrier handle toward you, and pull the carrier from the chassis. Remove the four screws that hold the air baffle to the carrier. A B C Figure 19. Removing the Air Baffle from the Drive Carrier A. [. . . ] Turn off all peripheral devices connected to the system. Turn off the system by pressing the power button. Unplug all AC power cords from the system or from wall outlets. Label and disconnect all cables connected to I/O connectors or ports on the back of the system. [. . . ]