User manual MAXDATA MPL 500 MAINBOARD

[. . . ] MAXDATA PLATINUM SERVER Mainboard Users' Manual MAXDATA PLATINUM Server Mainboard Manual 1 2 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Server Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Back Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Server Board Connector and Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Last State means the server will power up as it was powered when AC was lost. Power On means the server will always power up when AC is regained. If Clear OK, then display "System Event Log Cleared!" If Clear failed, then display "System Event Log Not Cleared!" Error Log Initialization <Enter> Table 22. Feature Wake On Event Submenu Selections Choices Disabled Enabled Disabled Enabled Direct Via Modem Description Enables remote power on via network command. Enables remote power on via serial port. Indicates whether the console is connected directly to the system or if a modem is used to connect. Wake On LAN Wake On Ring Console Connection Boot Menu Boot Menu options allow the user to select the boot device. The following table is an example of a list of devices ordered in priority of the boot invocation. Items can be re-prioritized by using the up and down arrow keys to select the device. Once the device is selected, use the plus (+) key to move the device higher in the boot priority list. Use the minus (-) key to move the device lower in the boot priority list. MAXDATA PLATINUM Server Mainboard Manual 31 Table 23. Boot Device Priority Submenu Selections Device ATAPI CD-ROM Drive Removable Devices Hard Drive Intel® Boot Agent, Version 4. 0. 17 Description Attempts to boot from an ATAPI CD-ROM drive. Attempts to boot from a removable device. Attempts to boot from a hard drive device. Attempts to boot from a network connection. Requires the presence of a PXE server. Boot Priority 1 2 3 4 Table 24. Hard Drive Submenu Selections Device Hard Drive 1* Hard Drive 2* Hard Drive 3* Bootable Add in Card Description Select the order in which each drive is attempted to be used as the boot device. Auto-detected Add-in card. Boot Priority 1 2 3 4 * These selections change depending on the system configuration. Table 25. Removable Devices Submenu Selections Device Legacy Floppy Drives Description Select the order in which each removable device attempts to be used as the boot device. These selections will change depending on the system configuration Boot Priority 1 Exit Menu You can make the following selections on the Exit Menu. Select an option using the up or down arrow keys; then press <Enter> to execute the option. Pressing <Esc> does not exit this menu. You must select one of the items from the menu or menu bar to exit. Table 26. Choices Exit Menu Selections Description Exit after writing all modified Setup item values to CMOS. User is prompted if any of the setup fields were modified. Load default values for all SETUP items. Read previous values of all Setup items from CMOS. Write all Setup item values to CMOS. Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 32 Configuration Software and Utilitiels Upgrading the BIOS Preparing for the Upgrade Before you upgrade the BIOS, prepare for the upgrade by recording the current BIOS settings, obtaining the upgrade utility, and making a copy of the current BIOS. Recording the Current BIOS Settings 1. [. . . ] Front Panel Header Connection Location A. SLP BTN ­ Sleep Button RST SW ­ Reset Switch PW SW ­ Power Switch HDD LED ­ Hard Disk Drive LED F. PWR LED ­ Power LED G. SCL Table 29. Location A B C D E F G H I Front Panel Header Connection Descriptions Pins 23 & Gnd 21 & 19 17 & 15 13 & 11 9&7 5&1 12 & 14 16 & Gnd 18 & Gnd Description The non-maskable interrupt Pressing the sleep button immediately puts the server board into the sleep mode. Pressing the reset button restarts the boot process. [. . . ]