User manual MAXDATA P1200 3200 BOARD

[. . . ] MAXDATA PLATINUM SERVER Mainboard Users' Manual MAXDATA PLATINUM Server Mainboard Manual 1 2 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Server Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Back Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Server Board Connector and Component Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use for viewing and clearing the system event log, viewing the system management FRU information, or viewing the system management SDR repository. Use to update the Field Replacement Unit (FRU), Sensor Data Record (SDR), and SM BIOS (SMB) flash components. Use to upgrade the BIOS. BIOS Setup System Setup Utility (SSU) FRUSDR Load Utility BIOS Upgrade Utility Firmware Update Utility Use to update the Firmware. Use to configure or view the settings of the SCSI host adapters and onboard SCSI devices in the server. Using the Adaptec SCSI Utility Hot Keys Use the keyboard's numeric pad to enter numbers and symbols. Table 5. To do this: Clear memory and reload the operating system this is a system reset. Secure your system immediately. Hot Keys Press these keys <Ctrl+Alt+Del> <Ctrl+Alt>+hotkey (Set your hot key combination with Setup. ) MAXDATA PLATINUM Server Mainboard Manual 45 Power-On Self-Test (POST) Each time you turn on the system, POST starts running. POST checks the server board, processor, memory, keyboard, and most installed peripheral devices. During the memory test, POST displays the amount of memory that it is able to access and test. The length of time needed to test memory depends on the amount of memory installed. After the memory test, these screen prompts and messages appear: Press <F2> key if you want to run SETUP If you do not press <F2> and do NOT have a device with an operating system loaded, the above message remains for a few seconds while the boot process continues, and the system beeps once. Then this message appears: Operating system not found If you do not press <F2> and DO have an operating system loaded, the boot process continues, and this message appears: Press <Ctrl><A> to enter SCSI Utility 4. Press <Ctrl+A> if there are SCSI devices installed. When the utility opens, follow the displayed instructions to configure the onboard SCSI host adapter settings and to run the SCSI utilities. Also see "Using the Adaptec SCSI Utility" on page 71. If you do not enter the SCSI utility, the boot process continues. Press <Esc> during POST to pop up a boot menu when POST finishes. From this menu you can choose the boot device or enter BIOS Setup. After POST completes, the system beeps once. What appears on the screen after this depends on whether you have an operating system loaded and if so, which one. If the system halts before POST completes running, it emits a beep code indicating a fatal system error that requires immediate attention. If POST can display a message on the video display screen, it causes the speaker to beep twice as the message appears. Note the screen display and write down the beep code you hear; this information is useful for your service representative. For a listing of beep codes and error messages that POST can generate, see the "Solving Problems" chapter in this manual. 46 Configuration Software and Utilities Using BIOS Setup This section describes the BIOS Setup options. [. . . ] This feature is used in the rare case that a BMC update requires a BMC Boot Block update as well. These pins should not be jumpered for normal operation. Jumper Name BMC Boot Block Update Table 9. Configuration Jumper (CN48) Pins 1-2 What it does at system reset When CN48 pins 1 and 2 are OPEN (default), FRB operation is enabled. This allows the system to boot from another processor if Processor 1 fails. When they are CLOSED, FRB2 and FRB3 are disabled. Jumper Name Disable FRB Timer Table 10. Configuration Jumper (CN49) Pins 1-2 What it does at system reset When CN49 pins 1 and 2 are OPEN (default), the BMC enters operational mode upon the negation of its reset. [. . . ]