User manual MAXDATA P1500 CASE

[. . . ] MAXDATA PLATINUM 1500R Server Case User's Manual MAXDATA PLATINUM Server Case User's Manual 1 2 MAXDATA PLATINUM Server Case User's Manual Part 1 Server Case MAXDATA PLATINUM Server Case User's Manual 3 4 MAXDATA PLATINUM Server Case User's Manual Content 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 What Your Kit Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Items You Must Purchase Separately . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Slide the carrier/drive all the way into the drive bay with the retention lever in the fully open position. Push the retention lever closed to secure the carrier/drive in the bay. Reinstall a carrier/air baffle in any bays where you are not installing a carrier/drive. 40 Assembling the System Installing a CD-ROM Drive/FDD Module Your server does not come with a CD-ROM drive or floppy disk drive. As an accessory, Intel® offers a slim-line CD-ROM drive/FDD module that you may purchase and install in the flex bay. Remove the filler panel and plug from the front of the chassis. Slide the module into the flex bay until you feel the connectors touch. Push the module in about 3/16 of an inch (5 mm) more to fully engage the connectors. If you have finished your work in the peripheral bays, install the bezel. Figure 25. Installing a CD-ROM Drive/FDD Module MAXDATA PLATINUM Server Case User's Manual 41 Installing a Bezel Place the bezel between the chassis handles and push it toward the front of the chassis until it snaps into place. Figure 26. Installing the Bezel 42 Assembling the System 3 Installing the System in a Rack Equipment Rack Precautions CAUTION ANCHOR THE EQUIPMENT RACK: The equipment rack must be anchored to an unmovable support to prevent it from falling over when one or more servers are extended in front of it on slide assemblies. The equipment rack must be installed according to the manufacturer's instructions. You must also consider the weight of any other device installed in the rack. MAIN AC POWER DISCONNECT: You are responsible for installing an AC power disconnect for the entire rack unit. This main disconnect must be readily accessible, and it must be labeled as controlling power to the entire unit, not just to the server(s). GROUNDING THE RACK INSTALLATION: To avoid the potential for an electrical shock hazard, you must include a third wire safety grounding conductor with the rack installation. If server power cords are plugged into AC outlets that are part of the rack, then you must provide proper grounding for the rack itself. If server power cords are plugged into wall AC outlets, the safety grounding conductor in each power cord provides proper grounding only for the server. You must provide additional, proper grounding for the rack and other devices installed in it. OVER CURRENT PROTECTION: The server is designed for an AC line voltage source with up to 20 amperes of over current protection. If the power system for the equipment rack is installed on a branch circuit with more than 20 amperes of protection, you must provide supplemental protection for the server. If more than one server is installed in the rack, the power source for each server must be from a separate branch circuit. CAUTION Temperature: The operating temperature of the server, when installed in an equipment rack, must not go below 5 °C (41 °F) or rise above 35 °C (95 °F). Extreme fluctuations in temperature can cause a variety of problems in your server. MAXDATA PLATINUM Server Case User's Manual 43 Ventilation: The equipment rack must provide sufficient airflow to the front of the server to maintain proper cooling. [. . . ] Ne faites pas fonctionner le système tandis que le boîtier est ouvert. Une fois TOUTES les étapes précédentes accomplies, vous pouvez retirer les panneaux du système. Si un cadenas a été installé sur à l'arrière du système, déverrouillez-le et retirez-le. Retirez toutes les vis des panneaux et mettez-les dans un endroit sûr. [. . . ]