User manual MAXDATA P2200R CASE

[. . . ] MAXDATA PLATINUM Server Case Users' Manual 2 Contents 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 What Your Kit Includes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Insert the cable in the cable clip (**), route it to the backplane, and connect it to the matching connector. Connect the USB cable (F) to the USB connector on the server board. Route the cable along the chassis floor at the bottom of the chassis sidewall (*). Connect the system fan cables (G) to their server board connectors. If you have installed a tape drive, connect the tape drive power cable (D) to the drive. Installing the Fan Assembly CAUTION When installing the fan assembly, avoid pinching cables routed in the area. Ensure the USB cable is routed in the corner where the chassis floor meets the sidewall. Position the fan assembly as shown in Figure 13 and lower it to the chassis floor. While pressing down on the fan assembly, slide it (A) toward the chassis sidewall. Check for the following: · The floor tabs have engaged the holes in the bottom of the fan assembly. · The latch tab (B) has engaged the chassis slot and locked the fan assembly in place. 24 Assembling the System Figure 13. Connect the fan power cables to the server board at the system fan connectors (Figure 14). Figure 14. Connecting Fans to the Server Board 6. Connect the USB cable to the 10-pin USB connector on the server board. MAXDATA PLATINUM Server Manual 25 Installing the Power Cord and Strain Relief Strap NOTE If you will be placing your server in a rack, wait to install the power cord until after the server is in the rack. Insert the expansion nipple (A) of the strain relief strap into the chassis hole. Plug the power cord into the power supply but not into the power source. Insert the power cord into the plastic loop (B) of the strain relief. Pull the plastic band (C) until it tightens around the power cord. To release the plastic loop and free the cord, squeeze the release lever (D). Figure 15. Installing the Power Cord and Strain Relief Strap Adding Components to the Server Board After installing the server board, you must add the desired number of processors and memory DIMMs. For instructions, see the Intel® Server Board Quick Start Guide that shipped with your server board. NOTE Once the server board and its components are installed, you are done assembling the system unless you have optional peripherals or add-in cards you wish to install. If you need to install these components, continue on to the next section. Otherwise, install the cover and bezel and continue on to Chapter 3, "Installing the System in a Rack" . 26 Assembling the System Installing Peripherals Peripherals and add-in cards are not included in your system and must be purchased separately. [. . . ] Turn off all peripheral devices connected to the system. Turn off the system by pressing the power button. Unplug all AC power cords from the system or from wall outlets. Label and disconnect all cables connected to I/O connectors or ports on the back of the system. [. . . ]