User manual MAXDATA P5200 CASE

[. . . ] MAXDATA PLATINUM 5200 Server Chassis User's Manual MAXDATA PLATINUM 5200 Server Chassis 1 2 Contents 1 Chassis Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Feature Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chassis Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In Europe, the cord must be less than 4. 5 meters (14. 76 feet) long, and it must be flexible <HAR> (harmonized) or VDE certified cordage to comply with the chassis' safety certifications. · · Chassis Security To help prevent unauthorized entry or use of the server, the chassis includes two chassis intrusion switches that can be monitored by Server Management software, a padlock loop at the rear of the chassis, and a front bezel door lock (pedestal only). Monitoring Two chassis intrusion switches are preinstalled. When the access cover is removed or the front bezel door is opened, the switch transmits a signal to the BMC on the server board. Server management software can be programmed to respond to an intrusion by powering down or by locking the keyboard, for example. 14 Chassis Description Mechanical Locks A padlock loop on the rear of the chassis access cover can be used to prevent access to the inside of the chassis. A variety of lock sizes can be accommodated by the . 270 inch (7 mm) diameter loop. The front bezel has a two-position lock to prevent access to the hard drives and the interior of the chassis. Figure 8. B. Front bezel locked Front bezel unlocked MAXDATA PLATINUM 5200 Server Chassis 15 16 Chassis Description 2 Setting Up the Chassis Install the Chassis Feet (Pedestal Mode) If you are installing this server into a rack system, skip these steps and read the instructions that came with your rack kit. Move the chassis to the edge of your workbench. Use four screws to attach each foot to the chassis. The holes in the feet will line up with only one set of holes in the chassis. On the front foot, the middle hole should be towards the front of the chassis. Hole locations for the front foot are marked "F" and "1, 2". On the back foot, the middle hole should be towards the back of the chassis. Hole locations for the rear foot are marked "F". You are now ready to attach a monitor, keyboard, and mouse to your server, and turn it on. D Figure 9. D. Screw hole Chassis foot Workbench Screw (M4 round head) MAXDATA PLATINUM 5200 Server Chassis 17 Install into a Rack (Rack Mode) NOTE Your chassis is designed to be compatible with the EIA-310-d rack standard. Be sure to select a rack cabinet enclosure that is EIA-310-d compliant. Remove the smallest and inner-most rail. Insert and tighten four screws. Figure 10. Install the rest of the rail in your rack. Figure 11. Rack Rail Assembly Mounting Holes 18 Setting up the chassis NOTE Your rack may vary from the illustration. Refer to your rack documentation for information specific to your rack. Hold the chassis so the rails on the chassis engage the rails in your rack. [. . . ] There are no serviceable parts in the power supply. Return to manufacturer for servicing. Fans CAUTION To avoid injury do not contact moving fan blades. Electrostatic Discharge (ESD) CAUTION Perform the procedures in this chapter only at an electrostatic discharge (ESD) workstation, because the server components can be extremely sensitive to ESD. If no such station is available, you can reduce the risk of electrostatic discharge ESD damage by doing the following: · · · · · · · Wear an antistatic wrist strap and attach it to a metal part of the server. Touch the metal on the server chassis before touching the server components. [. . . ]